7 Other Functions
MITSUBISHI CNC
II - 66
The positions of the P0 to P10 points in the chuck/tailstock are as follow.
(a)Setting the chuck
If a spindle section is not to be set, set the P3, P7 and P8 values to the same values, and the P6, P9 and P10
values to the same values. The barrier range will be as shown below in this case.
(b)Setting the tailstock
i) For external claw
ii) For internal claw
P0: Workpiece rotation center coordinate
P1, P2, P3: Chuck section (left)
P7, P8: Spindle section (left)
P4, P5, P6: Chuck section (right)
P9, P10: Spindle section (right)
- Set the X axis coordinates so that P1 > P2 > P3 is established.
- The P3 and P7 Z coordinates and the P6 and P9 Z coordinates shall be equal.
- If there is no spindle inner diameter, set the P8 X coordinate to the same value as P0.
i) For external claw
ii) For internal claw
- P7 and P9 are not used.
- The tailstock end section angle is set with the parameters.
"#8318 STOCK ANGLE (L)"
"#8319 STOCK ANGLE (R)"
- If "0" is set, the angle will be 90°. (Default)
- Set the P8 X coordinate to the same value as P0. (No spindle inner diameter)
P0
P1
P2
P3
P7
P8
P4
P5
P6
P9
P10
P0
P1
P2
P3
P7
P8
P4
P5
P6
P9
P10
P0
P1
P2
P3,P7,P8
P4
P5
P6,P9,P10
P0
P1
P2
P3,P7,P8
P4
P5
P6,P9.P10
P0
P1
P2
P3
P8
P4
P5
P6
P10
Содержание E70 Series
