E70 Series Instruction Manual
Appendix 7.10 Editing-related Operation Messages
IV - 157
Message
Details
MDI no setting
- Editing of the MDI was started, but the MDI setting was incomplete.
Abs/Inc mode is illegal
- During playback editing:
G90 was set when control parameter "Playback G90" was OFF.
G91 was set when control parameter "Playback G90" was ON.
MDI search complete
- The MDI search completed.
Can't search in MDI mode
- The restart search was attempted during MDI mode.
- Execute the restart search after switching other than MDI mode.
MDI Set ended
- MDI setting was completed.
MDI Setting error
- MDI setting cannot be executed.
MDI search error
- Could not execute the MDI search.
MDI entry complete
- MDI entry has been completed.
Can't edit except in MDI mode
- "#1144 mdlkof" (MDI setting lock) is "0" and therefore it is not possible to edit
the MDI program in a mode other than MDI mode.
Input miss was detected
- An input miss was detected.
Input miss was not detected
- A search was performed for an input miss, however, none was found.
Can't edit a file except in NC memory
- Editing cannot be performed at the edit window for programs other than those
in the NC memory.
Save it
- The cursor was tried to move beyond the editable range during mass-editing.
Save, then operate again.
Save not possible
- A special file (history file etc.) that cannot be saved was edited and an attempt
was made to save it. Perform an operation to quit editing.
- Failed saving due to file size over, etc. during mass-editing.
- Setting of "#1166 fixpro" was illegal. Use the settings for a regular program.
- MDI cannot be entered due to MDI editing mode. Press INPUT key and finish
editing.
Save left side file? (Y/N)
- Message to confirm whether saving the left side file of the multi-program
display type
[Y]: Save the change
[N]: Do not save the change
Save right side file?
(Y/N)
- Message to confirm whether saving the right side file of the multi-program
display type
[Y]: Save the change
[N]: Do not save the change
Can't edit because of size over
- The program cannot be written, because the memory capacity will be exceeded.
- If the memory capacity of the transfer designation device is exceeded during
the automatic backup, increase the available memory of the device.
Can't edit the searched file
- The serial file cannot be edited.
DS not ready
- Operation was attempted when a DS was not inserted.
- Creating or opening a program was attempted when a DS was not inserted.
FD not ready
- The FD operation search was attempted when an FD was not inserted.
- The FD list display was attempted when an FD was not inserted.
- Creating or opening a program was attempted when an FD was not inserted.
Содержание E70 Series
