3 Setup Screens
MITSUBISHI CNC
I - 156
Menus (Manual tool length measurement 1(Simple operation mode))
Menu
Details
Type
Reference
This displays the operation message "Input offset No". Input an offset No.
and press the [INPUT] key. The following value is written as the tool
compensation amount, and which item to write is determined by the
selected mode. Then the wear amount is cleared to "0".
A
Carrying out tool
length measurement
(Manual tool length
measurement I:
Basic point method)
Carrying out tool
measurement
(Manual tool length
measurement I:
Measurement value
input method)
<Manual tool length measurement I: Basic point method>
"Measure value"
<Manual tool length measurement I: Measurement value input method>
"Measure value" - "Work meas"
"Measure value" and "Work meas" will be cleared after the compensation
amount is written. The cursor moves to the tool compensation data.
Tool compensation amount cannot be written in the following cases. The
operation message "Can't write compensation data" displays.
(a) When the wear data is being displayed
(b) When the axis to measure is not selected
- If the measurement result exceeds the setting range, writing
compensation amount fails. The operation message "Setting error"
displays.
Set the offset No. and press the [INPUT] key. Then the tool compensation
data are listed with the Nos. placed at the top.
This operation will not change the column where the cursor is placed.
If this operation is carried out with the cursor placed at "Work meas", the
cursor will remain displayed at "Work meas".
A
Setting the Tool
Compensation Data
Select the axis to measure. The menu is highlighted when it is selected.
Multiple axes can be selected.
To cancel, press the menu key again or press [Cancel value].
(Note 1) The axis name to be displayed follows the parameter "#1013
axname"
B
Carrying out tool
length measurement
(Manual tool length
measurement I:
Basic point method)
Carrying out tool
measurement
(Manual tool length
measurement I:
Measurement value
input method)
Select the axis to measure. The menu is highlighted when it is selected.
Multiple axes can be selected.
To cancel, press the menu key again or press [Cancel value].
(Note 1) The axis name to be displayed follows the parameter "#1013
axname".
B
Carrying out tool
length measurement
(Manual tool length
measurement I:
Basic point method)
Carrying out tool
measurement
(Manual tool length
measurement I:
Measurement value
input method)
Select the axis to measure. The menu is highlighted when it is selected.
Multiple axes can be selected.
To cancel, press the menu key again or press [Cancel value].
(Note 1) The axis name to be displayed follows the parameter "#1013
axname".
B
Carrying out tool
length measurement
(Manual tool length
measurement I:
Basic point method)
Carrying out tool
measurement
(Manual tool length
measurement I:
Measurement value
input method)
Displays wear data in the tool offset data.
B
Displays length data in the tool offset data. Length data is displayed when
the power is turned ON.
B
Offset
write
Offset
No.
Measure
X
Measure
Z
Measure
C
Wear
data
Length
data
Содержание E70 Series
