E70 Series Instruction Manual
4.4 Program Input/Output
I - 271
(12) When "#8936 Delete leading 0" is set to "1", if a file name consisting only of numerical figures is input, "0" at the
head of the file name is deleted to be checked. However, if the file name is out of the range between 1 and
99999999, the leading "0" is not deleted. This applies to a machine tool builder's macros.Therefore, for example,
while the program "1" is in automatic operation, if a file name to transfer (input) is named "0001", the operation
message "Executing automatic operation" will be displayed, and transfer cannot be carried out. In the case of fixed
cycles, regardless of the setting of "#8936 Delete leading 0", the name of the file to transfer must be 9 digits, and it
must not start from "0". Attempting to transfer a file whose name does not satisfy the conditions above will cause an
error.
(13) If a file to be transferred (input) is subject to edit lock (Edit lock B: 8000 to 9999, Edit lock C: 9000 to 9999), the
operation message "Edit lock B" or "Edit lock C" will appear and it cannot be transferred.
If "#8936 Delete leading 0" is set to "1" and the program name consisting only of numerical figures is input, "0" at
the head will be deleted and checking will be performed. (Example: If the transferring (inputting) file name is
"008000", the operation message "Edit lock B" will be displayed and it cannot be transferred.)
(14) The transfer range from the external device other than serial to NC memory will change depending on the value set
in the user parameter "#19006 EOR Disable".
-
When the user parameter "#19006 EOR Disable" is set to "0", the head line will not be transferred.
Up to "%" in the second line onward will be transferred, and data after "%" will not be transferred.
If there is no "%", all data will be transferred.
-
When the user parameter "#19006 EOR Disable" is set to "1", all file contents will be transferred.
Содержание E70 Series
