Hudson 1948 - 1952 Скачать руководство пользователя страница 92

Страница: 92 / 333

4. Disconnect vacuum line from carburetor to distributor.

5. Disconnect heat riser line from exhaust manifold to

carburetor.

6. Remove nuts and lock-washers from the carburetor

mounting studs and remove carburetor assembly.

DISASSEMBLY:

1. Remove fast idle cam and pin assembly, Figure 9

FIGURE 9

2. Remove air horn and climatic control assembly, Figure

10, and lift off air horn gasket.

FIGURE 10

3. Disconnect throttle connector rod; then remove bowl

cover with all parts attached. Remove throttle shaft arm
assembly.

FIGURE 11

4. Check throttle connector rod for wear at both ends and

at hole in pump arm. Remove bowl cover gasket and

pump spring.

FIGURE 12

5. Remove the metering rod jet and gasket assembly, Figure 12.

FIGURE 13

4 - 8 FUEL SYSTEM & EXHAUST

Содержание 1948 - 1952













































































































































































































































































































































Результаты поиска

Содержание 1948 - 1952

Отзывы:

Бренды по названию

Популярные бренды

Hudson 1948 - 1952, Руководство по обслуживанию

Результаты поиска

Содержание 1948 - 1952

Отзывы:

Бренды по названию

Популярные бренды