manualshive.com logo in svg

Hudson 1948 - 1952, Руководство по обслуживанию

Поделиться
Скачать
Hudson 1948 - 1952 Скачать руководство пользователя страница 36

2 - 16   ENGINE TUNE-UP  

3. Set carburetor  throttle lever adjusting screw so engine will 

idle approximately 400 R.P.M.

4. Increase engine R.P.M. by carefully rotating the accelera-

tor bellcrank while watching the voltmeter gauge.

NOTE: When the voltmeter reacts at any point between 
6.4 to 7 volts the circuit breaker points should close and 
the ammeter will now show that the generator is charging. 
When the circuit breaker points close, a slight drop back 
of the voltmeter needle will be noticed. In the event  the 
drop back is not evident, slightly discharge the battery and 
recheck

5. Next slowly reduce the engine speed and watch the 

ammeter.

NOTE: When the ammeter reads 4 to 6 amperes, negative 
side of zero, the circuit breaker should open and the am-
meter needle will return to zero. Perform operations 4 and 
5 several times you are sure your readings are correct.

6. Proper adjustments can be made by bending the spring 

hanger on the breaker. See "Circuit Breaker Adjustment".

VOLTAGE REGULATOR CHECK:

1. Disconnect the battery wire at the voltage regulator" B" 

terminal and connect the test ammeter between the volt-
age regulator "B" terminal and the wire. disconnected. 

NOTE: Test ammeter resistance knob must be in the 
"Out" position before connecting test leads.

2. Connect the voltmeter positive lead to the regulator base 

and the negative lead to the regulator "B" terminal, Figure 

25.

FIGURE 25

3. Run engine at approximately 2000 R.P.M.
4. Turn resistor knob in until ammeter reads 18 amperes and 

then check the voltmeter reading which should    7.2 to 7.4 

volts. (Hot, cover in place).

NOTE: If car is out of warranty the voltage regulator  can 
be set by bending the spring hanger to get this necessary 
reading. The unit must be final-checked with the voltage 
regulator cap in place as generally it will change the 
reading from .1 to .2 of a volt and must be compensated 
for in making this adjustment.

5. Stop engine, disconnect battery  negative terminal and 

then proceed to remove the tester leads from the voltage 
regulator and Install the wires back onto the "B" terminal 

of the regulator.

6. Install the voltage regulator cover

VOLTAGE REGULATOR ADJUSTMENT:

1. To adjust the operating voltage remove cover and change 

the armature spring tension by bending the lower spring 

hanger. Increasing tension raises the operating voltage; 
decreasing the tension lowers it.

2. Replace cover and re-check.
3. After each adjustment of the voltage regulator, stop and 

re-start it. Bring engine up to 3000 R.P.M. and adjust 

current to 15 amperes before taking a reading.

CURRENT REGULATOR CHECK:

 Disconnect the battery wire at the regulator "B" 
terminal and connect the test ammeter between the 

voltage regulator "B" terminal and the wire disconnected, 

Figure 26.

FIGURE 26

Содержание 1948 - 1952














































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды