Hudson 1948 - 1952 Скачать руководство пользователя страница 183

Страница: 183 / 333

TRANSMISSION 8 - 5

3. Remove governor at speedometer gear housing on cars

equipped with Over-drive, Drive Master or Vacumotive
Drive.

4. Remove universal joint companion flange nut and com-

panion flange from mainshaft.

DO NOT HAMMER: Use Universal Joint Companion
Flange Puller, Tool No. J-820, to remove a tight flange
from mainshaft, Figure 3

5. Remove four screws and lockwashers and lift trans-

mission cover off cautiously to prevent the shift rail

lock spring from jumping out. Remove the spring

and lock ball.

6. Flush out and thoroughly clean inside of case and gears.

7. Re move speedometer gear housing cap screws and

speedometer gear housing using care to prevent damag-
ing the housing oil seal. Remove the speedometer drive

gear.

8. Remove 2nd and high shift rail stop screw.

FIGURE 4

9. Remove lock screw from low speed shifter fork an d lock

screw from the low speed shifter, Figure 4.

NOTE: To remove these special self-locking screws, use
a screw-driver having a straight blade or a blade with a
slightly reverse taper

will enter to bottom of screw slot.

"DO NOT USE A TAPERED BLADE SCREW
DRIVER."

10. Slide low and reverse shift rail out of front of case, then

remove shift fork and shifter, also the shift rail interlock.

11. Remove the set screw from 2nd and high shift fork, then

slide the shift rail out of front of case. Remove the lock
ball and spring from case.

FIGURE 5

12. Remove screw and countershaft and reverse idler gear

shaft lock plate, Figure (5).

FIGURE 6

13. Drive countershaft out of rear end of case with Bronze

Driver J-1574, Figure 6. Countershaft gear can now be
lowered to bottom of case.

Содержание 1948 - 1952













































































































































































































































































































































Результаты поиска

Содержание 1948 - 1952

Отзывы:

Бренды по названию

Популярные бренды

Hudson 1948 - 1952, Руководство по обслуживанию

Результаты поиска

Содержание 1948 - 1952

Отзывы:

Бренды по названию

Популярные бренды