manualshive.com logo in svg

Hudson 1948 - 1952, Руководство по обслуживанию

Поделиться
Скачать
Hudson 1948 - 1952 Скачать руководство пользователя страница 53

INSPECTION:

1. Remove all traces of old gaskets from oil pan trough and 

oil pan. Install new gaskets. (Apply a light coat of Hudson 

Perfect Seal Gasket Paste on both  sides of gasket when 
Installing new gaskets.)

FIGURE 9

2. Remove cotter pin (1) attaching FlotoScreen to outlet 

pipe. Clean screen thoroughly or replace.

3. Install Floto-Screen to outlet pipe. Check to make sure 

there is no binding action and screen swivels freely.

4. Secure ends of cotter pin.

Installation:

CAUTION: The cylinder block machining locating hole at 
the left rear side of the cylinder block base is so located 
that one half of the ho le opens into the crankcase. A cup 
shaped plug 9/16" outside diameter is used to close this 
hole after machining, Figure 10.

FIGURE 10

     Always check to see that this plug is in position when-
ever removing the oil pan.

  A new plug can be Installed (with J-483 vibration 

dampener Installer tool handle) from below the engine with 
the oil pan removed, or from above by removing the starter 

motor; always apply white lead or sealer to the cup before 

Installation; plug should be positioned as shown in Figure 
10.

1. Install synthetic rubber gasket on outlet tube.

2. Before Installing oil pan, place two quarts of recom-

mended oil in the oil pan troughs, and Install oil pan to 

engine, Installing two screws each side to hold oil pan 

until all screws have been entered.

3. Tighten screws evenly to 15-20 lbs. torque.

4. Raise jack until the #2 crossmember dowels are located 

and insert two front suspension attaching bolts (each 
side). Remove the six J-3228 Front Suspension Support 

bolts and Install the remaining standard bolts.

 If this part of the job is done properly, the alignment of 

the front suspension will not have been disturbed.

NOTE: Balance of Installation, reverse procedure of re-
moval. Refill engine with six quarts of recommended 
engine oil. This is in addition  to the two quarts placed in 
oil pan troughs.

OIL PAN

6 CYLINDER

REMOVAL:

1. Raise car and place stand jacks under the #2 frame 
 crossmember.

2. Remove the three bolts attaching the cen¬ter steering 

arm support bracket to #2 crossmember which will allow 

the center steering arm and tie rods to drop.

3. Remove two bolts attaching flywheel dust cover and 

remove cover.

4. Remove oil pan plug and drain oil.

5. Remove bolts  and lock-washers attaching oil pan to 

cylinder block, remove oil pan.

NOTE: Do not lose the round synthetic rubber gasket at 
oil outlet tube.

INSPECTION:

 Follow same procedure as outlined for 8 Cylinder Oil 
Pan Inspection.

ENGINE 3 - 11

Содержание 1948 - 1952














































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды