Hudson 1948 - 1952 Скачать руководство пользователя страница 169

Страница: 169 / 333

SECTION 7

CLUTCH

SPECIFICATIONS

Driving Plate Diameter

9" Used in Model 4B with Standard Transmission.
10" Used in Model 4B with Overdrive and Models

5B-6B-7B and 8B without Hydra-Matic Transmission.

Engaging Springs
9" Clutch 10" Clutch

Inner 6 Inner 3
Outer 9 Outer 12

CONSTRUCTION

All Hudson cars except those equipped with Hy-

dra-Matic Drive use a single plate, cork insert, oil

cushioned type clutch.

Details of the clutch may be seen in Figure 3.

Engagement and disengagement of the clutch is

controlled by the clutch foot pedal which is connected
by linkage to the shifter yoke (16). When the clutch

pedal is depressed, the yoke moves forward carrying
with it the throwout bearing (13) which bears against

the 3 throwout fingers (3) which react against the

retainers (5) to move the pressure plate away from the
driving plate and flywheel against the pressure of the

engaging springs (7). This action disconnects the driv-
ing plate (1) and drive gear (15) from the flywheel.

CLUTCH PEDAL ADJUSTMENT

To assure full disengagement of the clutch to
prevent clashing when shifting gears and also to pre-

vent the clutch pedal from riding against the floor

board, 1-1/2" clearance must be maintained between
the floor board and rear face of pedal, Figure 2.

This can be adjusted by loosening lock nut (A),
Figure 3, removing cotter pin and clevis pin (C) and

turning yoke (B) to increase or decrease the clearance
as required. Replace clevis pin and cotter pin and

tighten lock nut securely.

Engaging Spring Tension

(Compressed to 1-5/8"):
Inner

Outer
Engaging Fingers

Clutch Pedal Travel

Throwout Bearing.
Type

Type Fluid
Quantity

Filler Plugs (2)

Plate Facing
Number of Corks

Pilot Bearing

FIGURE 2

CLUTCH 7 - 1

75 to 85 lbs.

130 to 140 lbs.

1-1/4" - 1-3/4"

Ball Annular & Thrust

Single Plate in Oil

Hudsonite

1/3 Pint

Front of Flywheel

Cork Inserts

9"-90 - 10"-108

Ball

FIGURE 1

Содержание 1948 - 1952













































































































































































































































































































































Результаты поиска

Содержание 1948 - 1952

Отзывы:

Бренды по названию

Популярные бренды

Hudson 1948 - 1952, Руководство по обслуживанию

Результаты поиска

Содержание 1948 - 1952

Отзывы:

Бренды по названию

Популярные бренды