Hudson 1948 - 1952 Скачать руководство пользователя страница 40

Страница: 40 / 333

2 - 20 ENGINE TUNE-UP

FIGURE 33

3. Adjust by bending the rocker arm, Figure :14, using

Bending Tool T-1389 to obtain this clearance.

FIGURE 34

FAST IDLE ADJUSTMENT (WGD):

1. With the thermostatic coil housing, gasket and baffle plate

removed, open throttle valve (F), Figure 35, and hold choke
valve closed by holding arm down on choke lever (L).

2. Then close throttle. There should now be .026" clearance (use

gauge KMO-658-T-109 - 189) between the throttle valve and
bore of carburetor (side opposite idle port). Adjust by bending

the choke connector rod at lower angle (M).

FIGURE 35

FAST IDLE ADJUSTMENT (WA1):

1. With fast idle cam in normal idle position, tighten throttle

lever adjusting screw, Figure 36, until it just seats against
the cam.

FIGURE 36

Содержание 1948 - 1952













































































































































































































































































































































Результаты поиска

Содержание 1948 - 1952

Отзывы:

Бренды по названию

Популярные бренды

Hudson 1948 - 1952, Руководство по обслуживанию

Результаты поиска

Содержание 1948 - 1952

Отзывы:

Бренды по названию

Популярные бренды