Hudson 1948 - 1952 Скачать руководство пользователя страница 236

Страница: 236 / 333

9 - 28 OVERDRIVE

Remove solenoid cover and see if solenoid stem has been

forced past upper contact spring. Check pawl for release;

if pawl cannot be withdrawn freely from engagement, or
if the car cannot be pushed forward by hand, with one of

the forward transmission speeds engaged, the solenoid

unit has probably been damaged internally and must be
repaired or replaced. If no such damage is apparent and

the solenoid Installation appears proper, the solenoid
itself may be sticking. If car will roll backward -

B. Push overdrive dash control knob in, disconnect wire

from "A" terminal of generator and momentarily connect

loose end to negative post of battery by means of a
jumper. If overdrive relay and solenoid do not click,

follow procedure at E. If click occurs it indicates a circuit

ground between the relay and the governor or within the
relay or governor.

C. Pull overdrive dash control knob out and again momen-

tarily connect loose end of generator "A" terminal wire

to the negative post of battery. If no click occurs
grounded circuit is indicated between the control switch

and governor or within the governor; follow procedure E
and F. If click occurs -

D. Hold kickdown switch open,either by pressing the accel-

erator pedal to the floor, or by pressing the kickdown

switch stem by hand,and momentarily connect loose end

of generator "A" wire to negative post of battery. If no
click occurs; a grounded circuit is indicated between the

control switch and the kickdown switch; follow tracing
procedure F. If click occurs ground is indicated between

kickdown switch and relay or within one of these units;

follow procedure G and H.

E. With generator "A" wire connected to the negative post

of battery and overdrive dash control pushed in discon-

nect governor. If click occurs, replace governor. If no
click occurs at governor, replace connection, and discon-

nect governor wire at control switch. If click occurs,
inspect wire for ground; also inspect switch terminal for

grounding contact with some other part of the car. If no

click occurs replace connection, and -

F. With governor "A" wire connected as in E, disconnect

other wire at control switch; if click occurs inspect termi-

nal for a ground. If none is found replace switch. If no
click occurs disconnect harness plug from kickdown

switch. If click occurs a ground is indicated in either the

wire between the kickdown and the control switch or in
the kickdown switch. Connect test harness to overdrive

harness plug which was removed from kickdown switch
but do not plug into kickdown switch. Connect circuits 1

and 4 momentarily. If no click occurs, kickdown switch

is defective; if relay clicks the wire between the kickdown
switch and the control switch is grounded.

G. With generator "A" wire connected as in E, disconnect

harness plug from kickdown switch. If relay clicks, kick-

down switch is grounded. If there is no click the wire
between the relay and the kickdown switch or the relay is

grounded.

H. Connect test harness in system at relay and break the No.

2 circuit. If relay clicks the wire to the kickdown switch is
grounded, if it does not click relay is grounded and

should be replaced.

CONDITION NO. 9

WILL NOT kickdown FROM OVERDRIVE:

A. Ground No. 6 (3/1611 terminal screw) terminal of the

solenoid, with engine running. Press kickdown switch
stem by hand. If engine stops inspect connection at termi-

nal, and also contacts inside solenoid for proper closing
when stem is extended. If engine does not stop,Install test

harness at kickdown switch and ground No. 4 circuit.

When the No. 3 circuit is grounded engine should stop
when the throttle switch stem is pressed. If it does not,

replace switch. If the engine does not stop when either of

the terminals is grounded, wire or connections are defec-
tive between the throttle switch and the primary terminal

of the ignition coil. This connection is made to the pri-
mary terminal of the ignition coil that is connected to the

distributor.

Содержание 1948 - 1952













































































































































































































































































































































Результаты поиска

Содержание 1948 - 1952

Отзывы:

Бренды по названию

Популярные бренды

Hudson 1948 - 1952, Руководство по обслуживанию

Результаты поиска

Содержание 1948 - 1952

Отзывы:

Бренды по названию

Популярные бренды