manualshive.com logo in svg

Hudson 1948 - 1952, Руководство по обслуживанию

Поделиться
Скачать
Hudson 1948 - 1952 Скачать руководство пользователя страница 222

9 - 14  OVERDRIVE

(NOT THE SLEEVE) there should be .008" to .021" 
clearance between the lower end of the interlock plunger 
and the side of the pawl. The interlock plunger is fur-
nished in six different lengths, select a plunger of proper 
length to give proper clearance.

2. Install the adaptor lock ring (large) Figure 18.

NOTE: The adaptor lock rings are furnished in three 

thicknesses: .0625", .0665" and .0705", select the size 
required to obtain a tight fit in groove in the overdrive 
adaptor.

3. Install the solenoid by turning the solenoid counter-clock-

wise one quarter turn, Figure 17, but before Installing the 
cap screws, pull straight out on solenoid. If solenoid can 

be pulled out, the bolt at the end of the solenoid rod was 

improperly Installed (not locked in the pawl). Install lock 
washers and cap screws and tighten securely.

4. Install the sun gear, shift rail and fork assembly, Figure 

16. Check position of shift rail slots at assembly as shown 

in Figure 20. THIS IS IMPORTANT.

NOTE: If the shift rail assembly  has been disassembled, 
prick punch pin (2), Figure 20, securely in place before 
reInstalling assembly. Shifter fork should be a sliding fit 
in the sun gear collar groove

.

Installation OF ADAPTOR

PLATE. SOLENOID PAWL, SUN

GEAR CONTROL PLATE AND

BLOCKER. SOLENOID. SUN GEAR

SHIFT RAIL AND FORK

(Double Lever Type)

1. Install the adaptor plate and use one of the overdrive 

housing attaching screws to hold the adaptor in position. 

Install the solenoid pawl, sun gear control plate and 

blocker assembly, Figure 19.

2. Install the adaptor lock ring (large), Figure 18.

3. Install the solenoid by turning the solenoid counter-clock-

wise one quarter turn, Figure 17, and before Installing the 
cap screws pull straight out on solenoid. If the solenoid 

can be pulled out, the ball at the end of the solenoid rod 
was improperly Installed (not locked in the pawl).

4. Install the locking rail spring, "C " washer and plain 

washer on the shift rail and fork assembly.

5. Install the fork in the sun gear shift collar, and while 

holding the shift fork, shift rail and sun gear together, slide 

the sun gear onto the main shaft and the shifter rod into 
the hole in the overdrive adaptor.

Installation OF CLUTCH CAM.

PINION CAGE AND OVERDRIVE

MAINSHAFT

1. Install the clutch cam and pinion cage, attach the clutch 

cam to the pinion cage assembly with the large retaining 

clip, Figure 23.

FIGURE 23

2. Install the pinion cage and the clutch cam assembly on the 

main shaft and secure the assembly in place with the 
retaining clip, Figure 24.

FIGURE 24

NOTE: Replace any "U" clips that are worn or damaged.

Содержание 1948 - 1952














































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды