Hudson 1948 - 1952 Скачать руководство пользователя страница 50

Страница: 50 / 333

3. Drive out straight pin (10) which holds pump drive gear

(9) to shaft.

4. Press shaft (7) out of gear (9) by supporting oil pump

body (8) on cover face in a suitable arbor press allowing
inner rotor and shaft to clear when pressing shaft out of

gear.

5. Wash all parts in dry cleaning solvent and dry with

compressed air.

INSPECTION

1. Install rotors and shaft in pump body with inner rotor

rotated so that one lobe of inner rotor is contacting the
corresponding notch in the outer rotor. Measure clear-

ance between opposite lobe of inner rotor and outer
rotor. This clearance should be .010" or less. If more

than this, replace both rotors and shaft.

NOTE: The shaft, inner rotor, and outer rotor are sold
in matched sets only.

2. Measure thickness and diameter of outer rotor. This

thickness should be .873" or more and diameter 2.746

or more. If rotor measures less than these figures, re-
place with a new shaft assembly and new rotors.

3. Inner rotor thickness should be .873". If less than this

figure, replace with new rotors and shaft assembly.

4. With rotors and shaft assembled in pump body, place a

straight-edge across pump body between screw holes
and using a feeler, measure clearance between top of

rotors and straight edge. This clearance should be .004"

or less. If clearance is greater than this, replace oil pump
body.

5. With outer rotor (4) pressed to one side of pump body,

with feeler gauge, measure clearance between the outer

rotor and body at opposite side. This clearance should
measure .008". If clearance is more than this, replace

pump body.

NOTE: Inspection operations #4 and #5 should be made

after determining that the old rotor are satisfactory or
new rotors used.

6. Body cover (2) should be smooth. It should be replaced

if scratched, grooved, or worn. Lay a straight-edge across

the inner surface of cover and try to insert a .002" feeler

between cover and straight-edge. If feeler can be inserted,
replace cover.

ASSEMBLY:

1. Install outer rotor (4) in pump body, Figure 6.

2. Slide shaft (7) and rotor (5) assembly into pump body.

3. Support oil pump body and shaft, and rotors assembly on

a suitable clean surface and press oil pump drive gear (9)
on shaft (7). End play between hub of gear and pump

body should be .004" to .008".

4. Install gear pin, peening over both ends securely.

5. Make sure pump is thoroughly clean, then Install cover

gasket (3) in recess of pump body.

6. Install cover (2). Tighten screws evenly and securely.

Installation:

NOTE: lithe engine has been rotated after the pump has
been removed, the timing will be disturbed. It will then
be necessary to proceed as follows:

1. Remove distributor mounting screw and disconnect

octane selector tube. Remove distributor.

2. Set flywheel timing with #1 piston on T.D.C.

3. Insert aligning tool J-2794 in the distributor shaft hole

with aligning pin in line with the distributor mounting

screw hole, Figure 7.

3 - 8 ENGINE TUNE-UP

Содержание 1948 - 1952













































































































































































































































































































































Результаты поиска

Содержание 1948 - 1952

Отзывы:

Бренды по названию

Популярные бренды

Hudson 1948 - 1952, Руководство по обслуживанию

Результаты поиска

Содержание 1948 - 1952

Отзывы:

Бренды по названию

Популярные бренды