manualshive.com logo in svg

Hudson 1948 - 1952, Руководство по обслуживанию

Поделиться
Скачать
Hudson 1948 - 1952 Скачать руководство пользователя страница 60

  9. Disconnect the water temperature gauge wire from the 

side of the cylinder block.

10. Disconnect the oil gauge check light wire.

11. Disconnect the vacuum tube from the windshield wiper 

motor.

12. Remove the two generator lead wires.
13. Disconnect the coil wire.

14. Models 4B and 5B, remove the fan blade and water 

pump assembly.

15. Models 4B and 5B, disconnect the windshield wiper 

cables at wiper motor and remove wiper motor.

REMOVING CRANKCASE BREATHER:

1. Remove the screw holding the breather to rear tappet 

cover.
2. Remove bolt from bracket  attaching breather to engine 

end plate.

REMOVING RADIATOR:

1. On Models 6B, 7B, and 8B, disconnect the hood lock 

conduit pull wire at lower hood lock support.

2. Remove one Phillips head screw at top of front ornament 

and eight hexagon head sheet metal screws attaching the 
grille upper louver to the front fender tie panel (located 

under louver). Also remove the two Phillips head screws 
attaching the front fender tie panel center feeler to the tie 

panel.

3. Remove the eight hexagon cap screws from the fender tie 

panel and hood lock support panel and remove the tie 

panel.

NOTE: On Models 4B and 5B, remove the cotter pin, 
washer, spring and lock nuts attaching the hood support 
prop to the fender tie panel and radiator support channel.

4. Remove the four hex bolts attaching radiator to channel.

NOTE: Remove the nuts located inside the radiator channel.

5. The radiator may now be lifted up and forward out of the 

channel.

NOTE: Approximately 8" of forward clearance is gained 
by removing the radiator.

6. Remove the two front engine mounting bolt nuts and 

washers.

REMOVING CONNECTIONS BENEATH CAR: 

 1. Drain the transmission oil. (On Hydra-Matic transmis-

sions also drain torus cover).

 2. Drain engine oil from oil pan.

 3. Remove propeller shaft center bearing support bolts to 

allow rearward movement of the drive line to clear 
companion flange at transmission.

 4. Disconnect front propeller shaft at the transmission 

companion flange and at the rear axle remove propel-

ler shafts.

 5. Disconnect the speedometer. cable at transmission.
 6. Remove the bolt and bracket attaching, exhaust pipe to 

engine rear end plate.

 7. Remove two bolts from the clutch cross shaft bracket, 

disconnect clevis and remove cross shaft.

 8. Disconnect the shifter le ye r rods from transmission. On oars 

equipped  with Hydra-Matic transmission, disconnect the 

selector lever control rod and the transmission throttle rod 

and the outside throttle lever.

 9. Attach Motor Lift Bracket J-2782 and lift hoist hook, 

Figure 20.

10. Remove the engine (rear) mounting bolts. On cars 

equipped with the Hydra-Matic transmission, remove 

the No. 3 cross-member.

FIGURE 20

3 - 18   ENGINE 

Содержание 1948 - 1952














































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды