manualshive.com logo in svg

Hudson 1948 - 1952, Руководство по обслуживанию

Поделиться
Скачать
Hudson 1948 - 1952 Скачать руководство пользователя страница 309

BRAKES   15 - 3

    It is necessary that rod (5) which is attached to the brake 

pedal operating r o d, be adjusted for clearance where it seats 
in piston (13) so that there is 1/4" free movement of the 

brake pedal p ad before the pressure stroke starts. Cup (15) 
is thus permitted to be clear of port (16) when piston (13) is 

in its released position.

NOTE: If this port is not cleared by the piston, t he compen-

sating action of the master cylinder will be destroyed and the 
brakes will drag.

FIGURE 2

1. Filler cap
2. Filler cap gasket

3. Reservoir cover screws
4. Reservoir cover

5. Reservoir cover gasket

6. Push rod
7. Push rod guard strap

8. Push rod guard
9. Piston stop plate lock wire

10. Piston stop plate

11. Piston cup secondary
12. Master cylinder body

13. Piston
14. Inlet port

15. Piston cup primary

16. Outlet port
17. Piston spring

18. Check valve

    Secondary cup (11) prevents fluid from leaking out of 
master cylinder into boot (8). The supply tank filler cap (1) 

can be reached by raising the front floor mat and removing 
three self-tapping screws and lifting off the round floor cover.

FIGURE 3

NOTE: Master cylinder should be kept at least one half 
full of Hudson Hydraulic Brake Fluid. The filler cap and 
master cylinder should always be cleaned of all dirt and 
grit before removing the cap. Grit in the fluid will cause 
scoring of the cylinders and possible plugging of lines and 
ports.

BRAKE DRUM DUST SHIELD

    The brake drum dust shield is a press fit on the drum and 

is also staked in 4 equally distant places to the drum.

MASTER CYLINDER

REMOVAL:

1. Disconnect stop light wires at stop light switch (16) 

Figure 1 and brake tubes at rear of master cylinder con-

nector (15).

2. Remove one bolt attaching master cylinder frame bracket 

to frame rail and disconnect clutch pedal pull back spring.

3. Remove cotter key and clevis pin (10) attaching master 

cylinder push rod (12) t o pedal (8) and remove push rod 
(12).

4. Allow master cylinder (14) and bracket assembly to swing 

down and remove the two bolts (13), nuts and lockwashers 

attaching master cylinder to bracket.

Содержание 1948 - 1952














































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды