Hudson 1948 - 1952 Скачать руководство пользователя страница 115

Страница: 115 / 333

AIR CLEANER, DRY

(Oil Wetted Type)

The oil wetted type of air cleaner is used as standard

equipment on all models. In this type cleaner the wire gauze

is oil soaked. As the air passes through it, foreign particles
are removed, permitting only clean air to enter the carbure-

tor.

The air cleaner section should be cleaned at least every

2,000 miles, oftener if local conditions warrant.

This filter can be cleaned by removing the attaching wing
nut and lifting out the unit. Clean off old oil and dirt by

dipping in kerosene and blowing dry. Re-oil by dipping unit

in engine oil (using the same grade as is used in the engine).
Permit excess oil to drain off and reInstall unit in cleaner.

OIL BATH AIR CLEANER

The oil bath air cleaner is available as an option. In this

unit, dirt is precipitated from the air into the oil as the
incoming air strikes the oil in the sump.

The oil bath type air cleaner should be serviced at 2,000

mile intervals, or more, frequently during severe dust condi-

tions, as follows:
1. Unscrew and remove wing bolt at top of cleaner.

2. Lift out filter element; clean in gasoline and drain.

3. Remove old oil, wash out base, and refill to level indi-

cated with 50 S.A.E. oil for temperatures above 32° F

and 20 S.A.E. for lower temperatures.

FIGURE 103

FUEL PUMP

Carter mechanical fuel pump M-729SZ, Figure 103, is used as
standard on all "A" series Hudsons. A combination fuel and

vacuum pump, AC Type AJ, Figure 104, is available as an option.

Operation of the fuel pumps is similar. The pump cam lever (A)

fits under an eccentric on the camshaft. Rotation of the camshaft
forces the cam lever down against the diaphragm spring (B) pres-

sure, raising the diaphragm (C). Fuel is drawn into the fuel cham-

ber through the inlet port (D), screen (E), and inlet valve (F).
When the low side of the eccentric is against the cam lever, the

diaphragm spring forces the diaphragm down, expelling fuel
through the outlet valve (G) and outlet port (H) to the carburetor

bowl.

FIGURE 104

Continued pump operation fills the carburetor bowl, and the

float needle valve closes the carburetor inlet. Fuel pressure built up

in the pump fuel chamber opposes the diaphragm spring, resulting
in shorter strokes until the pump stops completely. Normal dia-

phragm stroke is about 1/64".

The vacuum section of the combination fuel and vacuum pump

acts as a vacuum booster for the windshield wiper. The same
eccentric and cam lever that operates the fuel pump operates the

vacuum pump. The cam lever forces the

FUEL SYSTEM & EXHAUST 4 - 31

Содержание 1948 - 1952













































































































































































































































































































































Результаты поиска

Содержание 1948 - 1952

Отзывы:

Бренды по названию

Популярные бренды

Hudson 1948 - 1952, Руководство по обслуживанию

Результаты поиска

Содержание 1948 - 1952

Отзывы:

Бренды по названию

Популярные бренды