Hudson 1948 - 1952 Скачать руководство пользователя страница 243

Страница: 243 / 333

REAR AXLE 11 - 1

SECTION 11

REAR AXLE

(Welded Cover Type)

SPECIFICATIONS

Drive Gear and Pinion Back-
lash

Pinion Bearings (Two)
Adjustment

Differential Bearing (Two)

Adjustment

.004" to .006"

Taper Roller

Shim

Taper Roller

Adjusting Nut

Wheel Bearings
Adjustment

Axle Shaft (End-Play)
Lubricant

Quantity

Taper Roller

Shim

.001" to .004"

S.A.E. 90 Multi-Purpose

(Gear Lubricant)

3-1/2 Pints

REAR AXLE RATIOS

Models 4B-5B

Standard Transmissions
With Hydra-Matic

Models 6B-8B

Standard Transmissions

With Overdrive

With Hydra-Matic

Model 7B

Standard Transmissions

With Overdrive

With Hydra-Matic

3-7/12

- - - - -

Std.

- - - - -

Std.

Opt.

- - - - -

Std.

4-1/10

Std

- - - - -

Std.

Opt.

- - - - -

Std.

Opt.

- - - - -

4-5/9

Opt.

- - - - -

Opt.

Std.

- - - - -

Opt.

Std.

- - - - -

CONSTRUCTION

The rear axle assembly is the semi-floating type with

Hypoid Helical gears mounted in a pressed steel banjo type

housing with adjustments provided for all bearings, ring gear
and pinion.

The drive pinion is supported by two tapered roller

bearings which are held in a correctly spaced position by the
pinion bearing spacer. Adjustment of the pinion and bearings

are provided for by a number of shims between the bearing

spacer and the front bearing and between the front face of the
pinion and the rear bearing. Oil leakage is prevented by a

hydraulic type, inner spring oil seal of chrome leather.

The ring gear is mounted on the differential case flange by
eight special alloy steel bolts. In order to insure quiet smooth

operation, the ring gear and pinion are supplied only in
matched sets.

The differential case assembly is suspended between two

tapered roller bearings, and is held securely by two carrier caps

and four bolts.

The splined end of the alloy steel axle shafts engage in the

differential side gears. The outer ends of the axle shafts are
tapered and are provided with keyways for attaching the rear

wheel hubs, which are supported by adjustable tapered roller
bearings pressed on the axle shafts. Side thrust from the

wheels is transferred from one shaft to the other by hardened

steel thrust buttons through the medium of the drive shaft
thrust spacer.

Rear wheel bearings are adjusted for end play by shims
inserted between the bearing caps and housing flange. Oil

leakage at this point is prevented by pressure type chrome

leather oil seals.
The axle housing is attached to the rear springs by means

of "U" bolts and is insulated to eliminate road and tire noise
by the use of rubber strips placed between axle and springs.

The general construction of the rear axle may be seen in the

illustrations which follow:

Содержание 1948 - 1952













































































































































































































































































































































Результаты поиска

Содержание 1948 - 1952

Отзывы:

Бренды по названию

Популярные бренды

Hudson 1948 - 1952, Руководство по обслуживанию

Результаты поиска

Содержание 1948 - 1952

Отзывы:

Бренды по названию

Популярные бренды