manualshive.com logo in svg

Hudson 1948 - 1952, Руководство по обслуживанию

Поделиться
Скачать
Hudson 1948 - 1952 Скачать руководство пользователя страница 28

2 - 8   ENGINE TUNE-UP  

DISTRIBUTOR

1. Remove the distributor cap from the distributor and thor-

oughly clean and examine the cap. Replace the cap if it has 

hairline cracks, carbon runners and badly burned or cor-
roded contact inserts.

2. Clean the spark plug cable sockets using KMO-230 Dis-

tributor Cap Terminal Cleaner. Clean any corrosion from 

the metal secondary contacts on the underside of the cap. 
If these contacts are badly burned or scored, replace the 

cap.

NOTE: If burning exists  on the horizontal face of the 
inserts or on t op of the rotor metal strip, it indicates that 
the metal strip of the rotor is too short and the rotor should 
be replaced.

3. Clean and inspect the rotor. Replace the rotor if the 

insulation is cracked or has carbon  tracks, or if the metal 

strip is badly burned.

CONTACT POINTS:

1. Inspect, clean and adjust the distributor breaker points. 

Replace burned or corroded points. Do not try to hone 

pitted contact points as refaced contacts do not have the 

finish for satisfactory performance.

NOTE: If points are badly pitted, check the condenser for 
over or under capacity. See "Electrical Section - Condenser".

2. When new contact points are Installed be sure they are 

properly aligned and that they make contact near the 
center of the contacts. Bend the stationary contact bracket 

to secure proper alignment. Do Not Bend  The Breaker 
Arm. Adjust the breaker point gap .020" for 6 cylinder 

distributors and .017" for 8 cylinder distributors. Breaker 

Arm fibre rubbing block should be on high pointof the 
distributor cam when checking adjustment of breaker 

points.

3. Apply a few drops of light engine oil to the wick located at 

the top of the distributor shaft, to the contact arm pivot 
and to the lobes of the cam. Do Not over-oil.

FIGURE 11

NOTE: Contact point adjustment is made by first loosen-
ing the clamp screw (B) Figures 11 and 12, holding the 
stationary contact plate, then turn the eccentric adjusting 
screw (D) to move the stationary contact  point. Tighten 
clamp screw when correct gap is secured.

FIGURE 12

Содержание 1948 - 1952














































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды