manualshive.com logo in svg

Hudson 1948 - 1952, Руководство по обслуживанию

Поделиться
Скачать
Hudson 1948 - 1952 Скачать руководство пользователя страница 191

TRANSMISSION  8 - 13

2. Place second and high shift fork in groove of synchro-

nizer shift sleeve and while holding the fork in this posi-

tion, insert the shift rail into case through hole in fork, 
Figure 27.

 Install and tighten slotted set screw using a straight blade 

screwdriver. Install rail stop screw and lock washer.

NOTE: The rail stop screw must not bottom on shift rail.

CAUTION: Make sure at this time that t he previously 
Installed inner shift shaft lever is correctly positioned. 
Inner shift lever and milled end of shift shaft should be in 
a true vertical position.

3. Install shift rail interlock plunger.

FIGURE 27

4. Start the low and reverse shift rail, into transmission case. 

Install low and reverse shifter in position and slide shift 
rail into shifter, Figure 28.

5. Place low and reverse shift fork in groove of low and 

reverse sliding gear and slide shift rail through hole in 

fork and into hole at end of case.

6. Install slotted head lock screw into shifter and tighten 

securely. Follow the same procedure on shift fork and 

lock screw.

7. Shift transmission into all 4 gear positions successively 

and also into neutral. If operation is satisfactory Install 
the remaining shift rail lock ball and lock spring.

8. Install transmission cover using a new gasket.

FIGURE 28

    Install clutch bell housing, (use new gasket). Tighten each 
of the 6 cap screws to 45 foot pounds.

    Install drain plug and insert 2-1/4 pounds of S.A.E. 80 
E.P. Winter or S.A.E. 90 E.P. Summer lubricant through 

filler plug opening. Install and tighten filler plug.

InstallING TRANSMISSION

1. Install two headless screws or studs in engine end plate to 

assist in supporting the the transmission at Installation.

NOTE: Before Installing transmission to engine rear sup-
port plate, check cylinder block rear support plate very 
carefully for tightness and alignment. This is especially 
important in cases where the car has been subject to 
chronic transmission trouble, noisy and jumping out of 
gear. Make a similar check of transmission clutch bell 
housing.

    In lieu of highly precise equipment, use a steel straight-

edge to check steel rear support plate and a surface plate or 
other flat surface to check the front face of clutch bell hous-

ing. Both units should be flat and in plane within .005".

 

   Be sure to check position of clutch driving plate and see 

that it is perfectly centralized within the clutch assembly. 
This can be done by using the J-449 aligning arbor or with 
a standard main drive gear if arbor is not available. If this 
precaution is not taken, difficulty will be encountered when

 

Installing the trans-

Содержание 1948 - 1952














































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды