Hudson 1948 - 1952 Скачать руководство пользователя страница 263

Страница: 263 / 333

REAR AXLE 11 - 21

4. Remove bolt s and take off differential bearing caps. Caps

and each side of housing are marked with either a figure

or a letter which must match when reassembling, Figure

18.

5. Place rear axle housing spreader (J-5231) in place on

housing with dial indicator mounted as shown and
spread housing .020" by turning the spreader screw. Do

Not spread housing more than this amount or leave

spreader expanded for a long period as this may cause
permanent damage. (Clamps should be used to hold the

spreader to the housing). Spreading the housing to re-

move or Install the differential assembly is necessary due
to the preload or side press of .005" to .009" between

bearing cups and housing.

FIGURE 40

6. Remove differential assembly by prying it upward with

two bars or large screwdrivers , placed under the differen-

tial case an d resting against the housing as shown. P r y
out assembly as straight upward as possible to prevent

damage, Figure 41.

7. Remove cups from differential side bearings. If bearing

cups and cones are not damaged or excessively worn and

are to be reassembled, be sure mating parts are paired
together.

8. Remove differential side bearing cones from case using

Puller J-2241-A and take off shims.

FIGURE 41

9. Pry up tabs on drive gear bolt locking plates, remove cap

screws and take off drive gear.

10. With a suitable punch, drive out lock pin securing differ-

ential pinion shaft in differential case, Figure 42.

FIGURE 42

11. Drive out differential pinion shaft and push out drive

shaft thrust spacer through inside of differential side gear.

12. Remove differential pinions, pinion thrust washers, dif-

ferential side gears and side gear thrust washers.

13. Turn axle housing on bench or in axle stand so drive

pinion is in vertical position.

Содержание 1948 - 1952













































































































































































































































































































































Результаты поиска

Содержание 1948 - 1952

Отзывы:

Бренды по названию

Популярные бренды

Hudson 1948 - 1952, Руководство по обслуживанию

Результаты поиска

Содержание 1948 - 1952

Отзывы:

Бренды по названию

Популярные бренды