Hudson 1948 - 1952 Скачать руководство пользователя страница 320

Страница: 320 / 333

15 - 14 BRAKES

22. Replace adjusting screw hole covers in the backing plate
and feeler gauge hole cover on the drum at all four wheels.

23. Install wheels and tighten wheel attaching bolts.

24. Install hub caps.

TROUBLE SHOOTING

BRAKE PEDAL GOES TO FLOORBOARD

Cause -

1. Normal wear of lining.

2. Improperly adjusted brake shoes.

3. Leak in hydraulic system.

4. Air in hydraulic system.

5. No fluid in system.

Remedy -

1. When it is necessary to pump the pedal several times

before the brakes take hold, it is an indication that the

brake linings are worn and that it is necessary to set the

shoes closer to the brake drums.

2. Shoes should b e set to .015" clearance. See "Major Brake

Adjustment".

3. A connection leak in the hydraulic system will allow the

brake pedal to go to the toe board gradually.

A cup leak does not necessarily result in any loss of the

travel of the pedal but will be shown by a loss of fluid in the

master cylinder.

If no leaks are found at the wheels or connections, remove
master cylinder and check the bore for scores or scratches.

4. Air in the hydraulic system will cause a springy or rubbery

action of the pedal. Should a sufficient quantity of air be

allowed to get into the system, the pedal will go to the toe

board under normal pressure.

In this case the hydraulic system should be bled.

5. The master cylinder should be checked for fluid. If the
tank ever becomes empty, air will get into the hydraulic

system making a bleeding operation necessary.

ALL BRAKES DRAG

Cause -

1. Mineral oil in system.

2. Porthole in master cylinder is closed.

Remedy -

1. The use of any oil having a mineral base (engine oil,

kerosene, gasoline, etc.) will cause the rubber piston cups

in master and wheel cylinders to swell and distort, mak-

ing them useless, and it is necessary to replace all piston
cups. Brake hoses will become swollen and plugged and

should be replaced.

NOTE: The system will have to be thoroughly flushed out
with clean alcohol and then refilled with "Genuine Hud-
son Hydraulic Brake Fluid"

2. The porthole (16) Figure 2 must not b e blocked by the

piston cup not returning to its proper release position.
Refer to "Brake Pedal Adjustment".

ONE BRAKE DRAGS

Cause -

1. Brake shoe return spring is weak.

2. Brake shoe set too close to the drum.

3. Wheel cylinder cups distorted.

4. Loose wheel bearings.

5. Dirt in the brake line.

Содержание 1948 - 1952













































































































































































































































































































































Результаты поиска

Содержание 1948 - 1952

Отзывы:

Бренды по названию

Популярные бренды

Hudson 1948 - 1952, Руководство по обслуживанию

Результаты поиска

Содержание 1948 - 1952

Отзывы:

Бренды по названию

Популярные бренды