manualshive.com logo in svg

Hudson 1948 - 1952, Руководство по обслуживанию

Поделиться
Скачать
Hudson 1948 - 1952 Скачать руководство пользователя страница 66

    The piston pin and connecting rod bushing should be 

replaced when necessary by selecting the proper size pin to 

fit the piston and reaming the connecting rod bushing to size.

NOTE: See "Connecting Rod Bushing Replacement" for 
proper procedure.

    Piston pins are furnished in standard, .002", .005", and 

.010" oversizes.
    Piston pins should be a hand push fit when piston is heated 

to 200° F.
    Heat the piston in boiling water or an electric furnace. 

NEVER heat piston with a blow torch as this will distort the 

piston.
    After fitting pins to pistons, check piston pin in connecting 

rod bushing. Ream bushing to .0003" larger than the pin 
diameter.

    Check the fit by holding the piston with the connecting rod 

in a horizontal position . The rod should just turn on the pin 
under its own weight.

PISTON PIN LOCK RINGS

    The piston pin is retained in the piston by two snap rings 

held in grooves at each end of the piston pin bore. This ring 
can be removed with any suitable pliers.

CONNECTING ROD BUSHINGS

(6 & 8 Cylinder)

    This piston pin bushing in the upper end of the connecting 

rod is of bronze; burnished in place, and broach finished on 

the 8 cylinder engine; and steel backed, bronze bushing, 
burnished in place and diamond bored on the 6 cylinder 

engine.

REPLACEMENT:

1. Press out old bushings by supporting the bushing end of 

the connecting rod on Bushing Burnisher Block J-2950 for 

6 cylinder and J-2951 for 8 cylinder.  Remove the bushing.

2. Install new bushings, reverse procedure of removal using 

the same tools required for removing.

3. After bushing has been pressed into the rod, using 

Burnisher Block J-2950, 6 cylinder and ,T-2951, 8 

cylinder  and with J-2791 Burnisher and Broach 6 cylin-

der and J-2949 Burnisher 8 cylinder iron the bushing in 
place in the rod, Figure 28.

NOTE: This operation swages or expands the bushing 
into eye of the rod. This is important as the bushings 
may work out of the rod if they have not been properly 
burnished in place.

FIGURE 28

4. Remove the bearing cap of the connecting rod and Install 

connecting rod on Aligning Fixture J-874-H arbor, 
1.9375"    8 cylinder, 2.2505" -- 6 cylinder. (Tighten rod 

on arbor and lock arbor in position with lock screw 
located on side of alignment fixture).

5. Insert the reamer pilot in the upper hole in the alignment 

fixture face plate and align bushing hole of rod with pilot 
hole in face plate.

6. Insert reamer pilot bushing in upper hole in fixture and 

lock lower arbor in place with locking handle.

7. Insert reamer through connecting rod bushing and into 

pilot bushing, Figure 29.

8. Perform reaming operation to the following dimensions:

        6 Cylinder -- .9685" to .9688"

        8 Cylinder -- .7496" to .750"

3 - 24   ENGINE  

Содержание 1948 - 1952














































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды