Hudson 1948 - 1952 Скачать руководство пользователя страница 269

Страница: 269 / 333

SECTION 12

FRONT SUSPENSION

SPECIFICATIONS

Curb height (Front)
(Rear)

Caster

Camber
Maximum variation between right and

left wheel caster or camber
Toe-In measured at wheel rim

Pivot Pin Inclination

Toe-out variation between wheels
Spindle Pivot Pin Thrust Bearing

Wheel Bearing Type

3-15/16"

5-1/4"

1/2° 1-1/2°

1/2º

0-1/16"

3º 36"

± 30"

Ball

Taper Roller

Wheel Bearing End Play
Tie Rod End Type

Tie Rod Adjust-

ment
Tie Rod Adjust-

ment
Steering center arm bolt

nut

Steering arm nut - tighten
to

.001" to .003"

Plain Bearing

To Increase-Turn counter clockwise

To Decrease-Turn clockwise

Tighten to 70# torque

#110 to 120# torque

CONSTRUCTION

Independent suspension of front wheels permits either wheel
to absorb road irregu1arities without any effect on the opposite

wheel.

Steering is from a center point which permits smooth opera-

tion of the steering mechanism. With the center steering arm, it
is possible to eliminate frictional points which is not possible

with off-center steering.

UPPER SUPPORT ARM:

The upper support arm and pivot are one unit, the assembly
rides in bushings located at the front and rear of pivot.

The upper support arm pivot bracket is attached to the frame

side member by three bolts. The outer end is attached to the

steering spindle support by the eccentric bushing pivot bolt.

STEERING SPINDLE:

The steering spindle and the steering spin dl e support are
joined together by the pivot pin. The steering spindle support is

attached to the upper support arm by the eccentric bushing bolt
and to the lower support arm by a pivot pin which rides in a

steel bushing.

LOWER SUPPORT ARM:

The lower support arms are responsible for the vertical

movement of the front suspension. They are joined to the

steering spindle support at the outer end and to a pivot that
is bolted to the #2 crossmember at the inner end.

The coil spring seat is riveted to the lower support arm and
the top of spring fits in a recess of the #2 crossmember.

Two rubber bumpers are located on the front suspension-

one limits downward movement of upper support arm - the

other limits upward movement of the lower support arm.

BUSHINGS:

The pivot pins and steel bushings are threaded and
therefore securely bound together even though excessive

wear may take a loose fit.

Clearance between pins and bushings i s from .012 to .026

to allow for lubrication adjustment and free action.

LUBRICATION

Lubrication of threaded bushings must be thorough and
with the weight of the car off the bushings.

FRONT SUSPENSION 12 - 1

Содержание 1948 - 1952













































































































































































































































































































































Результаты поиска

Содержание 1948 - 1952

Отзывы:

Бренды по названию

Популярные бренды

Hudson 1948 - 1952, Руководство по обслуживанию

Результаты поиска

Содержание 1948 - 1952

Отзывы:

Бренды по названию

Популярные бренды