Hudson 1948 - 1952 Скачать руководство пользователя страница 268

Страница: 268 / 333

11 - 26 REAR AXLE

30. Turn screw on housing spreader J-5231 and with dial

indicator mounted as shown in Figure 40, spread
housing .020" to permit installation of differential.

(Do Not spread more than this amount.)

31. Install differential assembly and bearings in housing.

To insure proper seating of bearings in housing, tap

drive gear with a rawhide or plastic hammer.

32. Install bearing caps, coating bolt threads with sealing

compound. Bearing cap marks must match those on

each side of housing, Figure 52. Remove housing
spreader and torque bearing cap bolts to 70 to 90 foot

pounds.

33. Install dial indicator on housing with butt on contact-

ing edge of drive gear tooth and check backlash

between gear and pinion, turning gear and measuring
in four places equally spaced around gear, Figure 52.

Backlash should range between .003" and .006" and
should not vary more than .002" between positions

checked.

34. Install housing cover using new gasket and placing

identification tag under one of the screw heads.

AXLE SHAFT ASSEMBLY

1. Install axle shafts using care when inserting them in

housing, not to damage new inner oil seals. Lubricate
wheel bearings and start outer cups in housing by

tapping with plastic or rawhide hammer. Use flange

bolts and brake backing plates to draw bearing cups
into place.

2. Place housing flange bolts in position and install shim

pack (right side only) removed during disassembly,

between brake backing plates and flanges.

3. Install wheel bearing oil seal cap gaskets, caps, lock

washers and nuts. Install new oil seals in caps and

tighten flange bolt nuts to 12-17 foot pounds.

4. Check axle shaft end play which should range between

.001" and .004". Change thickness of shim pack on

right side if necessary to obtain correct end play.
Shims are available in thicknesses of .003", .005",

.010" and .030".

INSTALLATION OF AXLE

1. Place axle assembly in position on rear springs, with

rubber cushions and retainers under spring seats. Engage
heads of

FIGURE 52

heads of spring center bolts in holes in center of axle spring

seats. If the rubber cushions have deteriorated, install new
ones.

2. Replace rear axle "U" bolts, lower spring plates, nuts and

lock nuts. Tighten nuts to a torque of 70-80 foot pounds.

3. Place roller jack under axle housing, elevate slightly and

connect rear shock absorbers at lower end.

4. Connect rear stabilizer to axle housing bracket.

5. Place rear universal joint needle bearing cups in position in

companion flange, install clamps, washers and nuts and
tighten nuts to 14-17 foot pounds torque.

6. Connect brake lines at rear wheel cylinders and brake hose

at frame connection. Bleed brakes.

7. Connect rear ends of parking brake cables to brake operat-

ing levers, position conduits and replace conduit caps.

8. Place brake drum and hub assemblies on axle shafts, install

washers and axle shaft nuts, tightening to 125 to 200 foot
pounds. Install and spread cotter pins.

9. Replace wheels, tighten hub bolts and install hub caps.

10. Remove housing cover filler plug and fill housing to level

of plug opening (3 lbs.) with S.A.E. 90 Hypoid or Multi-

Purpose Gear Lubricant. Replace plug and tighten filler
and drain plugs.

11. Install rear fender shields and lower car to floor.

Содержание 1948 - 1952













































































































































































































































































































































Результаты поиска

Содержание 1948 - 1952

Отзывы:

Бренды по названию

Популярные бренды

Hudson 1948 - 1952, Руководство по обслуживанию

Результаты поиска

Содержание 1948 - 1952

Отзывы:

Бренды по названию

Популярные бренды