Hudson 1948 - 1952 Скачать руководство пользователя страница 204

Страница: 204 / 333

8 - 26 TRANSMISSION

3. Carefully lower cluster and assembled parts into position

and enter front end of countershaft at rear of transmis-

sion case, tapping it forward while holding the front end
of the dummy shaft in constant contact with the counter-

shaft to keep needle rollers and washers in place. Drive
countershaft forward just far enough to enter front end

in case, as it must again be removed after checking end

play.

4. With a feeler gauge inserted between the rear thrust

washers, check countershaft cluster end play, Figure 43.

End play should range between .006" and .016"; if more

than this, the thrust washers should be replaced.

FIGURE 43

5. Next enter dummy shaft in front of case and by tapping
on shaft with a soft hammer, drive out countershaft through

rear of case, using care to keep ends of shafts together at all

times. Lower countershaft cluster with dummy shaft in
place, to bottom of case.

REVERSE IDLER GEAR

1. Place reverse idler gear in position in case (1 on g hub

toward front) and drive idler gear shaft in from rear of the

case. Before fully Installing shaft, make sure slot for lock
plate is properly aligned with countershaft so plate will

seat in both slots. Idler gear end play should be from
.003" to .010".

MAINSHAFT ASSEMBLY

1. Insert mainshaft with rear bearing assembled, through rear of

transmission case and Install low and reverse sliding gear,

with shift collar towards front of transmission.

2. Install low and reverse fork in rear shift lever shaft (offset to front)

and engage fork in groove of low sliding gear.

3. Install second speed gear.

4. Assemble synchronizer hub, shift plates, shift sleeve , springs and

synchronizer rings together as a unit and slide on mainshaft splines

the long hub of the sleeve pointing forward. Be sure that marks

painted on parts during disassembly are in proper alignment, also
that the hooked ends of the two synchronizer springs engage in the

same shift plate.

5. Install snap ring on front of mainshaft and check end play by

inserting a feeler gauge between the rear face of the mainshaft

second speed gear and the front ends of the mainshaft spiral
splines. This should be from .003" to .016". Excessive end play at

this point can only be corrected by Installing new parts.

6. Install second and high shift fork in second and high shift shaft,

move mainshaft and parts toward shift fork and engage fork in

groove of synchronizer shift sleeve.

7. Complete Installation of mainshaft and rear bearing in case by

tapping rear bearing outer race with plastic or rawhide hammer
until bearing case snap ring is flush with rear of case.

MAINSHAFT DRIVE GEAR ASSEMBLY

1. Coat inside of mainshaft drive gear and mainshaft front

rollers with lubriplate or heavy viscous grease and assem-

ble rollers (14) in position in gear.

2. Install mainshaft drive gear assembly tapping outer race of

bearing with a plastic or rawhide hammer until snap ring

in outer race is flush with front of case. When doing this,
be sure rollers are not dislodged before pilot end of main-

shaft enters drive gear.

COUNTERSHAFT Installation

1. To Install countershaft, insert two suitable punches through

countershaft holes in front and rear of transmission case,

Содержание 1948 - 1952













































































































































































































































































































































Результаты поиска

Содержание 1948 - 1952

Отзывы:

Бренды по названию

Популярные бренды

Hudson 1948 - 1952, Руководство по обслуживанию

Результаты поиска

Содержание 1948 - 1952

Отзывы:

Бренды по названию

Популярные бренды