Hudson 1948 - 1952 Скачать руководство пользователя страница 104

Страница: 104 / 333

4 - 20 FUEL SYSTEM & EXHAUST

4. Group all parts controlling pump operation, Figure 63.

FIGURE 63

5. Group all parts controlling choke operation, Figure 64.

NOTE: If welsh plug has been removed from the choke
housing for cleaning, Install a new plug.

FIGURE 64

FIGURE 65

1. Install all parts controlling IDLE OPERATION.

Install throttle shaft and lever assembly, Figure 65.

(Back out throttle lever adjusting screw.)

2. Install the throttle valves. Small "c" at (A), Figure

66, in circle should be toward idle port at (B) (when

viewing casting from manifold side). Center throt-

tle valves by tapping lightly and holding in place
with fingers before tightening screws. Always use

new screws. Peen threaded end of screws to keep
screws from loosening.

FIGURE 66

3. With throttle closed, press shaft from lever side and

Install throttle centering washer at "C", Figure 67,
prongs of washer extending outward. Press washer tight

against carburetor casting.

FIGURE 67

4. Install idle port rivet plugs (D), Figure 68. Then Install

idle adjustment screws and springs. (Adjust to specifica-

tions as shown on page 4-17, "Idle Adjustment").

Содержание 1948 - 1952













































































































































































































































































































































Результаты поиска

Содержание 1948 - 1952

Отзывы:

Бренды по названию

Популярные бренды

Hudson 1948 - 1952, Руководство по обслуживанию

Результаты поиска

Содержание 1948 - 1952

Отзывы:

Бренды по названию

Популярные бренды