Hudson 1948 - 1952 Скачать руководство пользователя страница 158

Страница: 158 / 333

6 - 22 ELECTRICAL SYSTEM

6. Remove breaker plate screws (C) and bearing retainer

clips, and lift out breaker plate.

Items 7 through 10 apply to both 6 and 8 cylinder

engines.

7. Remove oil wick from cam and remove hairpin retainer

from oil well.

8. Pull cam off shaft.

9. Remove centrifugal weights and springs.

NOTE: Use care to prevent distortion of springs.

10. Drive pin from collar or gear on shaft below distributor

housing and remove shaft from top of distributor.

ASSEMBLY, 6 and 8 CYLINDER

1. Install new shaft and bushings in distributor base if

clearance between shaft and bushings is greater than

.005". Soak bushings in engine oil for 15 minutes before
Installing shaft.

2. Install distributor shaft, thrust washer,. collar or gear

and pin.

3. Check distributor shaft end play for minimum of .010".

4. Install centrifugal weights and springs.

5. Install cam, hairpin retainer, and oil wick. Apply a

drop of engine oil to centrifugal weight pivots and

cam slots.

6. Pack breaker plate bearing 1/2 full of high melting

point grease and Install breaker plate, bearing retain-
ers and breaker plate screws. On 6 cylinder Models,

Install breaker points and condenser on breaker plate
before Installing plate. Install plate and distributor

cap clips and screws and Install primary lead screw.

(Do not allow wire from breaker arm to primary
terminal to ground on breaker plate.)

7. Install vacuum control unit.

8. Replace stationary contact, breaker arm, and con-

denser and adjust point gap.

9. Attach primary and condenser leads to clip on breaker

arm spring and check spring tension.

NOTE: Make sure ground wire (E), Figure 17, is se-
curely attached to upper and lower sections of breaker
plate and that condenser lead and mounting are tight.

10. Coat cam lobes lightly with water pump grease and

soak the oil wick with engine oil. Place a drop of light

engine oil on the breaker arm pivot.

11. Replace rotor.

Содержание 1948 - 1952













































































































































































































































































































































Результаты поиска

Содержание 1948 - 1952

Отзывы:

Бренды по названию

Популярные бренды

Hudson 1948 - 1952, Руководство по обслуживанию

Результаты поиска

Содержание 1948 - 1952

Отзывы:

Бренды по названию

Популярные бренды