manualshive.com logo in svg

Hudson 1948 - 1952, Руководство по обслуживанию

Поделиться
Скачать
Hudson 1948 - 1952 Скачать руководство пользователя страница 130

5 - 4   COOLING SYSTEM

FIGURE 2

WATER PUMP

(6 Cylinder)

    The water pump features a permanently lubricated ball 

bearing (18), Figure 3, for the pump shaft and non-adjust-
able packing (13). A permanent seal, which makes repack-

ing unnecessary, consists of a graphite washer (14) adjacent 
to the impeller (12), backed with a neoprene seal (13) and 

brass spring and retainer (8) for maintaining constant con-

tact on these two units. The graphite washer (14) is pre-
vented from turning in the impeller (12) and housing by 

means of four ears which are retained by four correspond-
ing slots in the impeller. The neoprene seal stops any fluid 

which might pass between the graphite washer and impeller.

    A large drain hole at bottom side of pump body allows 

for drainage and acts as a vent to minimize moisture forma-

tion in the pump assembly.

    The pump shaft is mounted in a permanently lubricated 
double row ball bearing with grooves in the shaft to furnish 

race-ways for the bearing balls and provide a means of 

taking end thrust of the fan and pump

 The bearing and shaft are retained in the pump housing 
by the shaft bearing retainer (6).

WATER PUMP REMOVAL:

1. Drain the cooling system by opening drain cock at lower 

right side of radiator and remove the pipe plug from left 
rear side of cylinder block.

NOTE: It is not necessary to remove the radiator to 
remove the pump; however, use care when removing and 
Installing the pump.

2. Loosen the bolt in the fan belt and generator adjusting 

bracket and move generator in toward the cylinder block 
to remove the fan belt.

3. Disconnect hose from the water pump inlet.

4. Remove the bolt and nut from the generator adjusting 

bracket to cylinder block and remove bracket.

5. Re move the four bolts and lock washers attaching fan 

blades to fan pulley and hub, and remove the fan blades.

6. Remove bolts attaching water pump to block and remove 

the water pump.

DISASSEMBLY:

1. Remove the water pump shaft retainer (6), cover (2), and 

gasket (3), Figure 3.

2. Place the water pump assembly in "Water Pump Holding 

Fixture J-2778, and using shaft driver contained in the set, 

press out the pump shaft and bearing assembly (18) with 

water pump pulley hub (19) attached.

NOTE: The fixture is designed to support the water pump 
body on a level plane while removing the shaft from the 
impeller. The height of the support stud is controlled by 
adjusting nuts which are run up on the stud to level the 
water pump body. The large hole in the base plate provides

Содержание 1948 - 1952














































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды