Hudson 1948 - 1952 Скачать руководство пользователя страница 292

Страница: 292 / 333

5. Loosen remote control tube bracket (lower) and jacket

tube clamp at steering gear, and remove jacket tube.

INSTALLATION:

Reverse procedure of removal.

FIGURE 5

STEERING GEAR

(Chuck Assembly)

REMOVAL:

1. Remove left front wheel and fender side dust shield.

2. Remove left frame to cowl brace.

3. Remove steering wheel and horn wire.

4. Remove steering gear jacket tube.

5. Remove three bolts (7), Figure 5, attaching steering gear

to side frame.

6. Remove key and plug from drag link (10) at pitman arm

and disconnect drag link.

7. Slide steering gear forward on frame and rotate to the left

until pitman arm is clear

8. Remove steering gear through wheel opening in left front

fender.

FIGURE 6

DISASSEMBLY:

1. Drain lubricant and mount assembly in a vise.

2. Using puller No. J-1374, Figure 6, remove pitman arm.

3. Remove gear shaft cover.

4. Cover serrations on gear shaft with waxed paper to

prevent damage to oil seal and remove gear shaft and

roller assembly.

5. Remove oil seal, needle roller bearings, and bearing

spacer from gear shaft housing.

6. Remove worm gear cover and grease retainer tube

assembly; use care to prevent damage to shims.

7. Remove lower bearing, bearing cup, worm and column

tube assembly, and upper bearing.

ASSEMBLY:

1. Clean inside of steering gear housing and all parts

before assembly.

2. Assemble upper bearing cup and bearing in housing

and

13 - 6 STEERING GEAR

Содержание 1948 - 1952













































































































































































































































































































































Результаты поиска

Содержание 1948 - 1952

Отзывы:

Бренды по названию

Популярные бренды

Hudson 1948 - 1952, Руководство по обслуживанию

Результаты поиска

Содержание 1948 - 1952

Отзывы:

Бренды по названию

Популярные бренды