Hudson 1948 - 1952 Скачать руководство пользователя страница 197

Страница: 197 / 333

TRANSMISSION 8 - 19

SECTION 8

TRANSMISSION

(Manual Type — Double Shift Lever)

CONSTRUCTION

It is of the all-helical gear type with synchro-mesh
second and high gears.

The rear of the mainshaft drive gear is supported by
a ball bearing mounted on its case and the front end is

piloted by a ball bearing in the flywheel. The front end
of the mainshaft operates in rollers carried in the main-

shaft drive gear and the rear end is supported by a ball

bearing in the case. Oil retention is by means of hydrau-
lic leather oil seals in the drive gear and rear bearing

retainers.

The mainshaft second speed gear and the reverse

idler gear operate on their shafts through precision
fitted, bronze alloy bushings. The countershaft gear

cluster operates on the stationary countershaft through

needle rollers at each end held in position by a spacer
tube and washers. Countershaft gear cluster end thrust

is taken by a single stationary, bronze faced thrust
washer at the front and by a rotating bronze washer and

a stationary steel washer at the rear.

Separate shift shafts with integral cams on the inside

and actuating levers on the outside, operate the low and
reverse and second and high gears through forks and an

interlock arrangement common to both shafts. Separate
rubber mounted rods connect the outer shift shaft levers

to the two levers on the transmission control.

The transmission is mounted on the clutch housing

with four bolts passing through lugs on the case from the
rear into the clutch housing. This simplifies transmis-

sion removal and replacement since the clutch housing
and floor cover do not have to be disturbed. Positioning

of the transmission on the clutch housing is through the

main drive gear bearing retainer, the outside of which is
a close fit in the hole machined in the clutch housing.

Breathing or venting is through a small opening in the front

of the cover and two holes in the rear of the gasket, which is
held away from the cover at the center by a depression

stamped in the cover.

GASKET THICKNESSES

Drive Gear Bearing Retainer:

.010", .015", .020" and .025"

Rear Bearing Retainer:

.010", .015", .020" and .025"

SNAP RING THICKNESSES

Mainshaft Drive Gear Bearing: .087", .090", .093" and

.096"

Mainshaft Rear Bearing:

.087", .090", .093" and .096"

Mainshaft Drive Gear:

.087", .090", .093", .096" and .101"

SPECIFICATIONS

GEAR RATIO

Low
Second

High

Reverse

2.571 to 1
1.684 to 1

1.000 to 1

3.489 to 1

INTERLOCK SLEEVES

MARKING

LENGTH

"A"

"B"

"C"

”D"

No Mark

1.295

1.291"

1.287"
1.303"

1.299"

LUBRICATION: 2-1/4 Pts. S.A.E.-90 Summer,
S.A.E. -80 Winter, Gear Oil.

Содержание 1948 - 1952













































































































































































































































































































































Результаты поиска

Содержание 1948 - 1952

Отзывы:

Бренды по названию

Популярные бренды

Hudson 1948 - 1952, Руководство по обслуживанию

Результаты поиска

Содержание 1948 - 1952

Отзывы:

Бренды по названию

Популярные бренды