Hudson 1948 - 1952 Скачать руководство пользователя страница 49

Страница: 49 / 333

FIGURE 5

1. Oil pump body

2. Oil pump body plug
3. Oil pump body plug gasket

4. Oil pump plunger
5. Oil pump shaft

6. Oil pump shaft bushing

7. Oil pump gear
8. Oil pump gear pin

9. Oil pump shaft bushing retaining screw

2. Remove the oil pump shaft (5) and bushing (6) retaining

screw (9), and remove the shaft and plunger (4).

3. Wash all parts thoroughly in gasoline and with an air

hose, blow parts dry.

REASSEMBLY:

1. Before assembly, dip the pump shaft and plunger in

engine oil.

2. Inlet connections at the cylinder block and at the oil

pump should be inspected. Leakage a t these points will,
cause air to be sucked into the system and the flow of oil

will be reduced and possibly stopped.

3. Install shaft and bushing, align hole of bushing with hole

in pump body and ball of shaft in hole in plunger.

Installation:

To Install, reverse procedure of removal.

OIL PUMP

6 CYLINDER

A centrifugal operating rotor type pressure pump is used

on all six cylinder engines.

REMOVAL:

To remove the oil pump and still maintain the correct
engine timing during Installation, proceed as follows:

1. Lift off distributor cap and rotate crankshaft until

distributor rotor is in firing position for #1 cylinder.

Keep engine in this position while pump is removed.

2. Remove the three oil pump to block attaching studs and

remove oil pump.

FIGURE 6

DISASSEMBLY:

1. Remove cover screws (1), Figure 6, cover (2), and gasket

(3).

2. Hold hand over cover opening and with pump upside

down, turn drive shaft until outer rotor (4) slips out.

ENGINE TUNE-UP 3 - 7

Содержание 1948 - 1952













































































































































































































































































































































Результаты поиска

Содержание 1948 - 1952

Отзывы:

Бренды по названию

Популярные бренды

Hudson 1948 - 1952, Руководство по обслуживанию

Результаты поиска

Содержание 1948 - 1952

Отзывы:

Бренды по названию

Популярные бренды