manualshive.com logo in svg

Hudson 1948 - 1952, Руководство по обслуживанию

Поделиться
Скачать
Hudson 1948 - 1952 Скачать руководство пользователя страница 230

9 - 22  OVERDRIVE

29. Remove retainer and select and Install a gasket .003" to 

.005" thicker than clearance indicated by feeler. (Gaskets are 

available in four different thicknesses.)

30. Place bearing retainer in position, Install 3 cap screws and 

tighten, making sure oil drain hole in flange is aligned with 

hole in case.

31. Install the transmission cover and gasket. The cover gasket  

has three vent holes and must be Installed with holes to rear 

of case. The cover has one vent hole and is Installed with 
hole to front of transmission. See marking on cover.

32. Complete balance of assembly as outlined under 

"Installation of Adaptor Plate, Solenoid Pawl, Sun Gear 

Control Plate and Blocker Solenoid, Sun Gear, Shift Rail 

and Fork, Clutch Cam, Pinion Cage and Overdrive Main-
shaft", Pages 13 and 14, also " Overdrive Housing Installa-

tion" , Page 15.

TRANSMISSION AND OVERDRIVE

Installation

1. Install two headless screws or studs in engine end plate to 

assist in supporting the overdrive and transmission at Instal-

lation.

NOTE: Before Installing the overdrive and transmission to 
engine rear support plate, check cylinder block rear support 
plate very carefully for tightness and alignment. This is espe-
cially important in cases where the car has been subject to 
chronic transmission trouble, noisy and jumping out of gear. 
Make a similar check of transmission clutch bell housing.

    In lieu of highly precise equipment, use a steel straightedge to 

check steel rear support plate and a surface plate or other flat 
surface to check the front face of clutch bell housing. Both units 

should be flat and in plane within .005".

    Be sure to check position of clutch driving plate and see that it 

is perfectly centralized within the clutch assembly. This can be 

done by using the J-449 aligning arbor or with a standard main 
drive gear if arbor is not available. If this precaution is not taken, 

difficulty will be encountered when Installing the transmission 
and the front end of the drive gear shaft and pilot bearing in the 

flywheel will be damaged.

2. Rotate clutch collar and throwout bearing to position 

for proper alignment with throwout yoke on transmis-

sion.

3. Tighten all rear engine support plate to block screws.

4. Bring the overdrive and transmission assembly to 

position where the main drive gear (clutch shaft) is 

aligned with bore of clutch throwout collar, then care-
fully push transmission forward to enter drive gear 

splined shaft through grease  retainer leather washer, 
splines of clutch driving plate and into pilot bearing in 

flywheel.

NOTE: During this operation the main drive gear must 
be relieved of all over hanging weight of the transmis-
sion until the bell housing engages the dowels on en-
gine rear support plate. Before transmission assembly 
is moved up against rear support plate make a last 
inspection to verify that end face of throwout collar in 
clutch is properly aligned with throwout yoke on trans-
mission and that oil seal lip has not turned under.

CAUTION: Alignment of bell housing with engine is 
controlled by the sleeve dowel in the upper left location 
of tile bell housing attaching bolt circle and by the 
dowel bolt at the lower right location viewed from rear 
of car. Make sure that the former is in place and 
entered in bell housing hole before tightening bolts. 
Install lower right bolt (dowel bolt) first. NEVER 
grind or otherwise reduce the diameter of the dowel 
bolt to facilitate Installation.

5. Remove the two headless screws or guide studs, J-2969.

6. Install remaining clutch bell housing bolts and screws 

and tighten with a torque wrench to 40-45 foot pounds.

7. Complete remainder of Installation by reversing the 

order of removal of the remaining parts. Check adjust-
ments and refill transmission and overdrive. A total of 

3-1/4 pounds of lubricant is required for the single 

lever type transmission and 3 pounds for the double 
lever type transmission.

Содержание 1948 - 1952














































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды