manualshive.com logo in svg

Hudson 1948 - 1952, Руководство по обслуживанию

Поделиться
Скачать
Hudson 1948 - 1952 Скачать руководство пользователя страница 54

Installation:

 Reverse procedure of removal. Check to make sure that 

center steering support bracket is properly secured.
 

 Refill oil pan with seven quarts of recommended oil.

CYLINDER HEAD

8 CYLINDER

REMOVAL:

1. Drain cooling system.

2. Loosen carburetor air horn attaching screw and clamp. 

Remove brace from opposite side and remove air cleaner.

3. Disconnect top radiator and by-pass hose.

4. Disconnect heater hoses (if so equipped).

5. Disconnect throttle rod at carburetor.

6. Disconnect temperature gauge wire at cylinder head 

sender unit.

7. Disconnect spark plug wires and remove spark plugs.

8. Remove cylinder  head stud nuts or cap screws and 

washers and remove cylinder head.

9. Remove temperature gauge sender unit from cylinder 

head.

CYLINDER HEAD

6 CYLINDER

REMOVAL:

     Follow the same procedure as outlined under "Cylinder 

Head Removal - 8 Cylinder" and in addition the following 

operation.
     

 Remove vacuum advance tube at octane selector.

Installation:

1: Make sure cylinder head is free from carbon and dirt. 

Check cylinder head with a straight edge for warpage or 

roughness, especially in cases of frequent "blowing" of 
head gaskets.

2. Install new head gasket.

CAUTION: Use the correct gasket - see that the gasket 
does not protrude inside the combustion chamber or 
cylinder bore line; also that water circulating holes on 
cylinder block face and holes in gasket line up.

NOTE: Cylinder head and gasket Installation on 6 
cylinder can be facilitated by using two J-2969 locating 
studs to position the gasket and head. These studs have 
a screw driver slot for removal after the cylinder head 
has been positioned, Figure 11.

FIGURE 11

 Cylinder head nuts should be tightened to 45-50 foot 

pounds on 8 cylinder and 60-65 foot pounds on 6 cylinder, 
using torque wrench J-1264.

 Tighten each nut or cap screw in the proper sequence 

shown in Figure 12.

 

 
       

FIGURE 12

3 - 12   ENGINE 

Содержание 1948 - 1952














































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды