manualshive.com logo in svg

Hudson 1948 - 1952, Руководство по обслуживанию

Поделиться
Скачать
Hudson 1948 - 1952 Скачать руководство пользователя страница 275

FRONT SUSPENSION   12 -7

plus not more than a five pound pressure from a horizon-
tal position. It must have n o perceptible shake. The pivot 
must not be rotated as this will throw the pivot off center 
with the support arm.

FIGURE 10

23. Eccentric bushing

25. Eccentric bushing pivot bolt
26. Upper support arm   

28. Upper support pivot and bracket
36. Upper support arm pivot bushings

49. Eccentric bushing seals

ECCENTRIC BUSHING

REMOVAL:

1. Place a jack under lower support arm and raise the car off 
the floor.

FIGURE 11

2. Remove eccentric bushing lock screw and washer (24), 

Figure 11.

3. Remove cotter pin, nut, and eccentric bushing pivot bolt 

(25).

4. Remove eccentric bushing seals (49).

5. Remove bushing (23) from the steering spindle support 

and upper support arm.

6. Remove eccentric bushing from steering spindle support 

using upper support arm eccentric bushing adjusting 

wrench "KMO- 366," Figure 12.

INSTALLATION:

1. Install eccentric bushing into steering spindle support 

(Hexagon head of bushing to the front).

2. Install eccentric bushing lock screw (24), but do not 

tighten.

3. Hold the steering spindle support in the center of the 

upper support arm and install the support arm pivot bolt. 

Turn the bolt until the head seats securely.

4. Install nut and cotter pin.

FIGURE 12

5. Use Wrench KMO-366 to adjust eccentric bushing. Ad-
just caster and camber.

6. Tighten lock screw securely.

NOTE: Turning the eccentric bushing two complete turns 
3/16" clockwise will give a plus 1° change of caster 
andtwo complete turns 3/16" counterclockwise will give 
a minus 1° change of caster.

Содержание 1948 - 1952














































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды