Hudson 1948 - 1952 Скачать руководство пользователя страница 250

Страница: 250 / 333

11 - 8 REAR AXLE

FIGURE 14

4. Remove differential bearing cap screws and lift out differ-

ential and ring gear assembly.

5. Remove differential bearing cones from case hubs using

bearing puller tool, J-2158, See Figure 14.

FIGURE 15

DIFFERENTIAL GEARS

1. Remove bolts which hold the ring gear to the differential

case.

2. Press ring gear off the differential case flange.

3. Remove bolts and lockwashers from differential case.

Separate the right and left hand case. See Figure 15.

4. All internal differential parts will then be loose and can

be removed by hand.

DRIVE PINION OIL SEAL

REMOVAL

NOTE: The pinion oil seal can be removed without re-

moving the pinion gear. This operation can be performed
on bench or under car with rear axle pinion oil seal re-
mover J -2647 as follows:

1. With companion flange holding tool J-2637 and J-2071

deep socket remove the drive pinion nut and washer as

shown in Figure 16.

FIGURE 16

NOTE: Under no condition place a wedge between the
ring gear and pinion teeth to lock pinion shaft while loos-
ening the drive pinion nut

2. Remove companion flange with puller J-820.

FIGURE 17

Содержание 1948 - 1952













































































































































































































































































































































Результаты поиска

Содержание 1948 - 1952

Отзывы:

Бренды по названию

Популярные бренды

Hudson 1948 - 1952, Руководство по обслуживанию

Результаты поиска

Содержание 1948 - 1952

Отзывы:

Бренды по названию

Популярные бренды