manualshive.com logo in svg

Hudson 1948 - 1952, Руководство по обслуживанию

Поделиться
Скачать
Hudson 1948 - 1952 Скачать руководство пользователя страница 39

ENGINE TUNE-UP   2 -19

3. Pump travel should be as follows:

8 Cyl. Carter WGD-773-S    5/16"
6 Cyl. Carter WGD-776-S    5/16"

6 Cyl. Carter WA 1-749-S    16/64"
6 Cyl. Carter WA 1-968-S    16/64"

6 Cyl. Carter WA 1-990-S    16/64"

    Use Carter Universal Pump Stroke Gauge T-109-117-S 

if available.
4. Adjust pump travel by bending the throttle connecting 

link at lower angle for WA1 carburetors and at the upper 

angle for WGD carburetors at (C), Figure 30.

METERING ROD SETTING (WGD):

NOTE: The metering rods must be adjusted after the 
pump travel adjustment or when leaner than standard 
rods are Installed. (No metering rod gauges are neces-
sary for this adjustment).

FIGURE 31

1. With the throttle lever set screw backed out as in "Pump 

Adjustment", press down on vacumeter link (1), Figure 
31, until metering rods bottom.

2. With mete  ring rods bottoming, revolve metering arm 

(K) until lip (H) (see insert) contacts vacumeter link (I). 

Hold arm (K) towards connector link side and carefully 

tighten the metering rod arm set screw (J).

METERING ROD SETTING (WA1):

1. Remove air cleaner and dust cover.

2. Remove hairpin clip and disconnect spring from metering 

rod.

3. Remove metering rod and disk.

4. Insert metering rod gauge, J-1265 (Carter No. T-109-102). 

Hold gauge vertical and be sure gauge is seated in meter-

ing rod jet, Figure 32.

5. Press down on vacuum piston link directly
over piston until it contacts the pump arm.

Clearance between metering rod pin and shoulder of gauge 

should be less than .005" with throttle valve seated. Gauge 

must not drag on pin.

6. Adjust by bending lip on piston link at (A).
7. Remove gauge and Install metering rod and disk.

8. Reconnect metering rod spring.

FIGURE 32 

ANTI-PERCOLATOR ADJUSTMENT (WA1):

NOTE: Carburetor must be removed from engine.

1. Crack throttle valve .020" by placing gauge .T-1633 

(Carburetor No. T-109-29), between throttle valve and 

bore of carburetor on side opposite the idle port, Figure 

33.

2. Clearance between percolator rocker arm lip and pump 

arm should be .005" to .015".

I L L U S T R A T I O N S   O N   T H I S   P A G E   C O P Y R I G H T  

1939 BY CARTER CARBURETOR CORPORATION.  A L L  

R I G H T S   R E S E R V E D .

Содержание 1948 - 1952














































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды