manualshive.com logo in svg

Hudson 1948 - 1952, Руководство по обслуживанию

Поделиться
Скачать
Hudson 1948 - 1952 Скачать руководство пользователя страница 255

REAR AXLE   11 - 13

6. Install bearing cones on differentials case hubs, using 

differential side bearing replacer J-2546 as shown in 

Figure 29.

7. Place differential case assembly in carrier and assemble 

differential bearing adjusting nuts.

8. Install differential bearing outer races and caps in place 

and insert bolts and lock-washers, drawing them up 
finger tight. (Make sure the bolts and lockwashers are in 

good condition).

9. Turn the left hand adjusting nut to the right (clockwise) 

until no play can be felt between ring gear and pinion.

10. Turn the right hand adjusting nut to the right 

(clockwise) and draw it up tight, using differential bear-

ing adjusting nut wrench J-972, See Figure 30.

FIGURE 30

11. Mount dial indicator, KMO-30 on the differential carrier 

flange. Turn left hand adjusting nut to the left 

(counterclockwise) one half notch. Turn right hand adjusting 

nut to the right (clockwise) one half notch.

NOTE: It is suggested that while this operation is 
being accomplished, the ring gear be rotated to allow 
the tapered bearings to seat properly.

FIGURE 31

12. Rest plunger of dial indicator on the outer edge of the ring 

gear tooth. See Figure 31. When moving the ring gear by 

hand, the back lash should be between .004" to .006". If 
the reading does not conform to recommended tolerances 

t u r n adjusting nuts one half notch at a time until desired 

reading is obtained.

NOTE: After setting the back lash tolerance, use a small 
brush and paint seven or eight teeth of the ring gear with 
red lead. Move the painted teeth of the ring gear over the 
pinion until a good impression of the tooth contact is 
assured. The impressions obtained on the gear teeth will be 
similar to those shown in Figure 32. With this illustration 
as a guide, make adjustments accordingly.

13. Tighten left bearing cap bolts. Turn right differential 

bearing. adjusting nut to the right (clockwise) one full 
notch.

This additional tightening provides the necessary .008" to 
.012" "Spread" to the differential carrier for proper opera-
tion.

14. Tighten cap bolts securely on right differential bearing 

cap.

Содержание 1948 - 1952














































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды