Hudson 1948 - 1952 Скачать руководство пользователя страница 242

Страница: 242 / 333

10 - 4 PROPELLER SHAFT

FIGURE 4

PROPELLER SHAFT CENTER

BEARING REPLACEMENT

If it is ever necessary to replace the propeller shaft center

bearing, proceed as follows:

1. Remove the center bearing retaining nut from sliding
spline at front end of rear shaft.

2. Remove center bearing mounting attaching bolt.
3. Disconnect universal joint at transmission companion

flange.

4. Remove front shaft by sliding off splines.
5. Remove the center bearing and housing assembly from

shaft.

NOTE: The center bearing is a press fit in the housing
and may be removed and replaced without difficulty.

6. Remove the lock rings from either side of bearing and

press bearing from housing. Use a tubular tool that clears
the inner race and press against outside race only.

NOTE: For Installation, reverse procedure of removal.

The specified torque for the center bearing compani on
flange bolt nut is 90-100 pounds.

PROPELLER SHAFT CENTER

BEARING SUPPORT CUSHION

These cushions are furnished in two Degrees of
Durometer hardness.

Red moulded or painted red Standard Production 40

Durometer Hardness. Both cushions on all models with

Black moulded 60 Durometer Hardness used on left side of
mounting for models equipped with Hydra-Matic transmis-

sions.

TROUBLE SHOOTING

PROPELLER SHAFT

Excessive Vibration

Improper alignment of flanges
Misaligned or sprung drive shaft

Worn torque tube bushing

Worn needle bearings in U-joint
Worn splines on the shaft or companion flange

Loose U-joint flange nut
Shifted rear axle

Spring frame

Excessive end thrust
Careless braking

Overloading the vehicle
Too short shaft

Improper lubrication

Metallic Rattle, Click, or Growling

Lack of lubrication

Worn universal joint seals

Broken or worn universal joint bearings Worn universal

joint cross

Universal joint bearings not seated properly in flange or

yoke

Propeller shaft support mounting studs loose
Propeller shaft support bearing worn, brinelled, or rough

Loose intermediate flange

Propeller shaft support improperly Installed (upside

down)

UNIVERSAL JOINTS

Out of Balance

Loose flange nut
Grease fitting interference Breakage

Erratic driving and braking High angle drive

Overloading
Weak rear springs

Misaligned drive shaft
Misaligned rear axle

Содержание 1948 - 1952













































































































































































































































































































































Результаты поиска

Содержание 1948 - 1952

Отзывы:

Бренды по названию

Популярные бренды

Hudson 1948 - 1952, Руководство по обслуживанию

Результаты поиска

Содержание 1948 - 1952

Отзывы:

Бренды по названию

Популярные бренды