Hudson 1948 - 1952 Скачать руководство пользователя страница 219

Страница: 219 / 333

OVERDRIVE 9 - 11

4. Remove the retaining clip at the end of the clutch cam,

Figure 14, this will allow removal of the cam and the
pinion cage assembly.

7, Remove the solenoid attaching screws, turn the sole-

noid one-quarter turn clock-wise and remove, Figure
17.

FIGURE 15

5. Remove the "U" clip located between the free

wheeling cam and pinion cage and separate these

units, Figure 15.

FIGURE 16

6. Remove the sun gear and shift rail assembly, Figure

16.

FIGURE 17

FIGURE 18

8. Remove the large snap ring at the adapter plate, Figure

18.

FIGURE 19

9. The retainer plate, the sun gear, control plate and blocker

assembly, and the pawl can then be removed, Figure 19.

10. The interlock lock plunger can be removed by lifting out

the plug at the adapter with a sharp punch. Remove

interlock by pushing it through the opening uncovered
by the plug. Use a stiff wire and work through the

opening uncovered by the solenoid.

Содержание 1948 - 1952













































































































































































































































































































































Результаты поиска

Содержание 1948 - 1952

Отзывы:

Бренды по названию

Популярные бренды

Hudson 1948 - 1952, Руководство по обслуживанию

Результаты поиска

Содержание 1948 - 1952

Отзывы:

Бренды по названию

Популярные бренды