manualshive.com logo in svg

Hudson 1948 - 1952, Руководство по обслуживанию

Поделиться
Скачать
Hudson 1948 - 1952 Скачать руководство пользователя страница 317

BRAKES   15 - 11 

    Check parking brake cables connecting to the rear brakes to insure 

that the cables have not been adjusted so short that the shoes have 
been moved off at their anchor in pin seal (in other words, the brakes 

are partially applied).

4. The brake pedal shank should not have more than 1/4" clearance 

with the brake pedal in its fully released position.

    The brake control lever should be against its stop when the push 
rod is 1-1/4" from its rear face to the front end of the push rod.

5. Check the anchor pin nut with a torque wrench to make sure it is 

tight. It should check 65-75 foot pounds.

NOTE: If an anchor pin nut is found loose, reset the anchor 
according to instructions under "Major Brake Adjustment".

6. Remove adjusting hole cover from the backing plate, Figure 12. 
Expand the brake shoes by turning adjusting screw. Move handle 

of Brake Adjusting Tool J-1028 as shown in Figure 13, until the 

brake drum can just be turned by hand, then back off adjusting 
screw moving handle of Tool J-1028 approximately 14 notches.

FIGURE 13

    Back off each screw the same number of turns.

NOTE: Make  this adjustment at all four wheels. The 
brake drum should turn freely and if there is a heavy drag 
between shoes and drum, reset the anchor pin as given 
under "Major Brake Adjustment".

7. Reinstall the adjusting hole covers in the backing 

plates.

8. With the hand brake fully released, the brake cables 
should permit the anchor ends of the rear brake shoes to 

rest on the anchor pin. If shoes do not rest on anchor 

pin, readjust the cables as follows:

    With the hand brake grip two notches from full 
release, 1/8" clearance should exist between hand brake 

cable lever (5) Figure 1, and end of slot in lever guide 

plate (24). If not - adjust hand brake cable clevis.

9. Pull rear brake cables tight and adjust ends so that 

clevis pins just enter holes in toggle (22). All slack 

should be removed when clevis pins are in place and 

hand brake applied two notches. Releasing hand 
brake will provide proper slack in cables.

    Examine hand brake ratchet rod lock springs to see 

that they engage properly in the rod ratchet. Replace 

springs if worn or broken.

10. Pull cables Light and adjust the ends so that the 

clevis pins just enter the holes in the toggle (35), 
Figure 1.

   
11. Release hand brake.

 

12. Reinstall wheels and lower the car.

    Test for operation on a level road. Do not test on the 
side of a crowned road.

NOTE: Lubricate brake cables with viscous chassis lu-
bricant.

MAJOR BRAKE ADJUSTMENT

 

    A complete brake adjustment is necessary when a 

minor adjustment fails to give satisfactory results or 

when replacing shoe and lining assemblies.

1. Jack up all wheels clear of the floor.

2. Remove wheels.

Содержание 1948 - 1952














































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды