Hudson 1948 - 1952 Скачать руководство пользователя страница 113

Страница: 113 / 333

pipe assembly (4) from the rear carburetor elbow to front

carburetor tee. Install the fuel pipe union (9) in the fuel

pump and connect fuel pipe assembly from fuel pump
to carburetor tee.

29. Install the throttle shaft assembly (12) to cylinder head

by removing the four cylinder head bolts (11 and 18);

place throttle shaft brackets (19) on cylinder head and
reInstall head bolts, torquing to 65 ft. lbs.

NOTE: If interference is caused by hanger on coil bracket
(13), bend the hanger back to provide necessary clearance
for throttle shaft.

30. Install the rear air cleaner support bracket (17) under the

cylinder head bolt as shown, and re-torque bolt.

31. Install the 45° hose nipple provided in the kit in the

cylinder head. Connect hose from Ranco valve to hose
nipple and Install the heater outlet pipe from hose to

water pump.

NOTE: It may be necessary to increase the bend in the
heater outlet pipe to allow hose to clear throttle return
spring and rod.

32. Install accelerator pedal link bellcrank assembly (23) to

bellcrank shaft (21) on the engine block and hook-up
throttle shaft operating rod assembly (22) from bell-

crank to throttle shaft.

33. Install linkage adjusting pin J-2544 through bellcrank

lever and into hole in cylinder block provided for adjust-
ment purposes. This pin serves to locate the bellcrank

while rod adjustments are made.

34. On cars not equipped with Overdrive transmission, the

accelerator pedal stop must be shortened by cutting
7/32" off end of the stop to permit wide open throttle.

35. Follow adjustment procedure as outlined under Car-

buretor and Linkage Adjustments.

36. Install air cleaners to front and rear carburetors and bolt

to cleaner braces.

Installation INSTRUCTIONS

(5B MODELS)

1. Follow steps 1 through 28 as outlined on the preceding

pages covering 6B an d 7B Installation Instructions.

2. Install the throttle shaft assembly (24) to cylinder head by

removing the four cylinder head bolts shown in Figure

101, placing throttle shaft brackets (25) on cylinder head

and re-Installing head bolts, torquing to 65 ft. lbs.

NOTE: If interference is caused by hanger on coil bracket
(26), bend the hanger back to provide necessary clearance
for the throttle shaft

3. Ins tall rear air cleaner support bracket (27) under the

cylinder head bolt as shown and re-torque bolt.

4. Install the 45° hose nipple, provided in the kit, in the

cylinder head and tighten so nipple faces forward at
approximately 15° above horizontal.

5. Remove Ranco valve to heater core hose and valve to

cylinder head hose and disconnect Ranco valve from

firewall. Install the two spacers, provided in the kit, to
the Ranco valve and reInstall valve to the firewall.

FIGURE 101

FUEL SYSTEM & EXHAUST 4 - 29

Содержание 1948 - 1952













































































































































































































































































































































Результаты поиска

Содержание 1948 - 1952

Отзывы:

Бренды по названию

Популярные бренды

Hudson 1948 - 1952, Руководство по обслуживанию

Результаты поиска

Содержание 1948 - 1952

Отзывы:

Бренды по названию

Популярные бренды