Hudson 1948 - 1952 Скачать руководство пользователя страница 272

Страница: 272 / 333

FIGURE 4

24. Eccentric bushing lock screw

25. Eccentric bushing pivot bolt

26. Upper support arm
27. Front wheel brake hose

2. Install coil spring (2), Figure 1.

NOTE: Flat end of spring must be at top. Bottom must
rest in lower support arm spring seat. Be sure silencer is in
upper spring seat.

When installing new springs or shims be sure to install new

silencers.

3. Lower the car, which will compress spring and position

lower support arm pivot (3) to frame cross-member.

4. Install lower support arm pivot attaching bolts (4) and

tighten securely.

5. Install shock absorber

FIGURE 5

26. Upper support arm Spring with red marking must be

28. Upper support arm pivot and bushing assembled on

right side of car.

29. Upper support arm pivot to frame bolts Springs with

white marking on

30. Shock absorber upper stud nut left side of car.

6. Install stabilizer connector (8).
7. Install tie rod end at steering arm (13).

8. Install brake backing plate (9).

9. Install wheel assembly and lower car.

When the car does not seem to be level and a check of
the coil spring height is desired, place the c a r so that

the front end is level crosswise, and then rock the car
sidewise several times and allow the car to settle. This

will remove any binding that might cause a dimensional

difference.

FIGURE 6

Measure the distance from the top of the lower support
arm rubber bumper seat to the bottom of the upper rebound

bracket, which should be 3-15/16" each side, Figure 6.

If the two measurements vary more than 1/2" between
sides, it is advisable to replace one or both coil springs.

NOTE: A daub of paint has been placed across the two
center coils of each spring as follows:

Spring with red marking must be
assembled on right side of car.
Springs with white marking on
left side of car.

12 - 4 FRONT SUSPENSION

RIDING HEIGHT AND COIL

SPRING SAG

Содержание 1948 - 1952













































































































































































































































































































































Результаты поиска

Содержание 1948 - 1952

Отзывы:

Бренды по названию

Популярные бренды

Hudson 1948 - 1952, Руководство по обслуживанию

Результаты поиска

Содержание 1948 - 1952

Отзывы:

Бренды по названию

Популярные бренды