manualshive.com logo in svg

Hudson 1948 - 1952, Руководство по обслуживанию

Поделиться
Скачать
Hudson 1948 - 1952 Скачать руководство пользователя страница 61

CAUTION: Be sure the engine lift bracket is safely 
attached to the engine and that chain fall hook is prop-
erly positioned with chain tight, Figure 20, as engine 
will tip when the No. 3 crossmember is removed.

11. Carefully remove engine out of chassis, Figure 20.

Installation:

1. Loosen bolts holding front motor insulators to cross-

member.

NOTE: This will allow proper front motor support 
alignment when entering motor to car.

2. Enter engine to car using care to enter at a proper angle.

3. Align engine with front motor support bolts, Install nuts 

and washers, but do not tighten at this time.

4. On Hydra-Matic equipped cars, raise rear of engine 

sufficiently to Install the No. 3 crossmember, Install 
bolts but do not tighten.

5. On cars equipped with standard transmissions, align rear 

motor support insulator with hole s in crossmember and 

Install spacers, flat washers, lock-washers, and nuts; 
tighten securely. On cars equipped with Hydra-Matic, 

Install the engine rear support bolts, attaching the rear 

insulators to the No. 3 crossmember (two each side). 
Tighten these bolts securely and then tighten the cross-

member bolts evenly and securely.

6. On cars equipped with standard transmissions, Install 

clutch cross shaft and bracket assembly.

NOTE: Use a new rubber bushing at clutch cross shaft.

7. Install clutch adjusting rod and make necessary adjust-

ment.

8. Install clutch pull back spring.

9. Install the shift lever rods to transmission. On cars 

equipped with Hydra-Matic, Install the outer throttle 

rod lever, throttle rod and selector.

10. Install speedometer driven gear and speedometer cable.
11. Install universal joint to transmission companion 

flange. Lock plates securely .

12. Install propeller shaft center support bracket and attach-

ing screws.

13. Install exhaust pipe flange at manifold before tightening 

clamp at transmission.

14. Tighten front motor support bolts to 40 lbs. torque.
15. Install oil pressure indicator contact (bakelite) and wire. 

Use care in tightening to prevent breakage.

16. Install exhaust pipe clamp at rear motor support.
17. Install flexible gas line.

18. Refill transmission as outlined in transmission section 

of Hydra-Matic Manual.

19. Lower car.

20. Remove motor lifting bracket.
21. Install oil gauge wire at check valve, coil wire, tempera-

ture gauge wire, generator wires, starter, starter c able 

and windshield wiper hose.

22. On first series cars, Install remote control cable to 

control tube and attach bracket to control lever support 
bracket.

NOTE: Shifter lever at steering wheel and transmission 
must be in neutral to insure proper shift.

23. Install Weather Control hose at water pump tube or at 

water pump.

24. Install air cleaner.
25. Install radiator and hose.

26. Attach headlight harness to junction post.

27. Install front fender tie panel assembly in reverse order 

of removal.

28. Attach hood lock release cable wire on cars so equipped.

29. Install accelerator rod at throttle bell crank.
30. Install hood, reverse procedure of removal.

31. Refill crankcase to recommended level. See 

"LUBRICATION", Section 1.

PISTONS. PINS. AND RINGS

ROD AND PISTON REMOVAL: (6 & 8 CYLINDER)

NOTE: Before removing rods and pistons, remove the 
ridge from the top of cylinder walls with an accredited 
ridge reamer. 

ENGINE 3 - 19

Содержание 1948 - 1952














































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды