manualshive.com logo in svg

Hudson 1948 - 1952, Руководство по обслуживанию

Поделиться
Скачать
Hudson 1948 - 1952 Скачать руководство пользователя страница 146

6 - 10   ELECTRICAL SYSTEM   

A. Cover Band
B. Armature Terminal Stud

C. Field Terminal Stud
D. Ground Screw

E. Pole Shoe Screw

F. Oiler
G. Bearing Retainer

H. Bearing Retainer Gasket
I. Bearing

J. Washer Retainer

K. Felt Washer
L. Woodruff Key

M. Through Bolts

CAUTION: The engine MUST NOT be run for more than a 
few seconds while making the above test, due to the danger of 
burning out the generator.
NOTE: If the above test is made with a resistor type tester, the 
resistance knob must be turned to the out position.

5. If generator fails to build up, remove generator for overhaul.

DISASSEMBLY:

1. Remove cover band

N. Brush Spring
O. Brush

P. Brush Lead
Q. Commutator End Head

R. Armature

S. Frame
T. Snap Ring Felt Washer

V, Bearing Retainer Screw
W. Drive End Head

X. Lockwasher

Y. Armature Shaft Nut
Z. Drive Pulley

2. Disconnect brush leads and remove brushes.

3. Remove through bolts and remove  commtator end head.

4. Remove armature and drive head. (If necessary, tap drive 

head end lightly with a soft hammer.)

 5. Remove shaft nut and lockwasher.

Содержание 1948 - 1952














































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды