Hudson 1948 - 1952 Скачать руководство пользователя страница 200

Страница: 200 / 333

8 - 22 TRANSMISSION

REMOVAL:

The transmission is removable from underneath the car, thus
eliminating the operation of removing and replacing the floor

cover and mat. The clutch housing also does not have to be

disturbed.

1. Remove drain plug and drain lubricant.

2. Remove nuts, washers and clamps from front universal joint

and disconnect propeller shaft. Use tape passed around both
bearing cups to hold bearing cups and needle rollers in place

and prevent entry of dirt.

3. Disconnect low and reverse and high and intermediate shift

rods at transmission shift levers.

4. Disconnect speedometer cable at transmission and remove

speedometer pinion.

5. Remove nut from front end of brake pivot brace at No. 3

crossmember.

6. Remove clevis pin at rear end of brace and move linkage to

left side of car. The additional clearance gained will aid in
lowering and removing the transmission.

7. With a universal socket on a 10" extension, remove the two

top bolts attaching transmission to clutch housing. Insert in

their places guide studs (J-2969) to guide transmission during

removal.

8. Lower transmission and clean outside thoroughly before

placing it on workbench or holding fixture for disassembly.

DISASSEMBLY :

1. Remove six screws holding cover and take off cover and

gasket.

2. Holding universal joint companion flange with holding tool

(J-2637), remove main-shaft nut, lock washer and plain
washer.

3. Remove companion flange, using puller (J-820), Figure 32.

FIGURE 32

4. Remove four bolts from mainshaft rear bearing retainer

and take off retainer and gasket. Remove speedometer

drive gear from mainshaft.

5. Remove three bolts holding main drive gear bearing

retainer and take off retainer and gasket.

6. Remove small snap ring from main drive gear.

7. With a brass drift and hammer, move countershaft rear-

ward just enough to free up the lock plate in the shaft
groove at the rear end, Figure 4.

FIGURE 33

Содержание 1948 - 1952













































































































































































































































































































































Результаты поиска

Содержание 1948 - 1952

Отзывы:

Бренды по названию

Популярные бренды

Hudson 1948 - 1952, Руководство по обслуживанию

Результаты поиска

Содержание 1948 - 1952

Отзывы:

Бренды по названию

Популярные бренды