Hudson 1948 - 1952 Скачать руководство пользователя страница 293

Страница: 293 / 333

install worm and tube assembly.

3. Install lower bearing and cup.

4. Install worm shaft cover shims and cover and grease

retainer tube assembly. If grease retainer tube is

equipped with silencer make sure silencer is installed on
tube.

5. Install gear shaft needle roller bearings and spacer.

6. Turn high point notch on steering column tube straight

down and install gear shaft and roller assembly.

7. Assemble thrust plate on adjusting screw into slot in

roller housing and attach gear shaft cover and oil seal.

8. Place pitman arm on gear shaft and tighten to 125 to 140

foot pounds.

9. Check worm for end play. if end play exists, adjust by

removing one worm cover shim at a time until end play
is eliminated. Rotate column tube after each removal to

determine if stiffness exists. Stiffness indicates removal

of too many shims.

10. Check gear shaft for excess play. If pitman arm can be

moved more than 1/32// without turning the steering
column tube, remove gear shaft adjustment screw lock

nut and lift lock plate clear of cover boss. (Check notch
on steering column tube to be sure it points straight

down.) Tighten adjusting screw just enough to remove

play between gear shaft and worm. DO NOT
TIGHTEN BEYOND THE POINT OF TAKING UP

LASH. Replace lock plate and lock nut and tighten nut.

11. Replace felt washer on column tube at steering gear

housing.

INSTALLATION:

1. Install steering gear assembly on frame and insert but DO

NOT TIGHTEN three bolts attaching steering gear to

frame.

2. Install steering gear jacket tube. Tighten tube in bracket at

instrument panel.

3. Tighten the three bolts attaching steering gear to frame to

50 to 60 foot pounds.

4. Loosen bolts attaching steering column bracket cap at

instrument panel to allow column

to shift to match position of steering gear and retighten bolts.

5. Replace horn wire and steering wheel with notch in

column tube straight down and wheel spokes horizontal.

6. Replace frame to cowl brace, dust shield, and front wheel.

7. Check front suspension for stiffness by placing front

wheels on roller plates and attaching spring scale to tire
thread. Maximum pull required to turn wheels with drag

link disconnected is 28 pounds.

8. Set front wheels in straight ahead position and attach drag

link to pitman arm. (See "Drag Link Adjustments", page
15-9).

9. F ill steering gear housing with S.A.E. 90 E.P. Lubricant.

PITMAN ARM

REMOVAL:

1. Remove key and plug from drag link at pitman arm and

disconnect drag link (10), Figure 5.

2. Disconnect battery cable at starting motor solenoid and

disconnect starter switch wire from solenoid.

3. Remove starting motor attaching bolts and remove start-

ing motor assembly.

4. Remove nut (1), Figure 5, and lockwasher attaching

pitman arm to steering gear.

STEERING GEAR 13 - 7

Содержание 1948 - 1952













































































































































































































































































































































Результаты поиска

Содержание 1948 - 1952

Отзывы:

Бренды по названию

Популярные бренды

Hudson 1948 - 1952, Руководство по обслуживанию

Результаты поиска

Содержание 1948 - 1952

Отзывы:

Бренды по названию

Популярные бренды