Hudson 1948 - 1952 Скачать руководство пользователя страница 120

Страница: 120 / 333

7. Lift vacuum diaphragm (30) out of body and remove

lower oil seal retainer (34), by turning until slot lines

up with flat of pull rod. Remove oil seal washer (32),

upper oil seal retainer, and oil seal spring (31).

8. Remove fuel diaphragm (2) by pulling straight out.

CAUTION: DO NOT TILT EXCESSIVELY OR
STAKED-IN OIL SEAL WILL BE DAMAGED.

9. Remove valve cage retainer screw (3), lift out retainer

(4), two valve and gauge assemblies (5) and two

gaskets (13).

10. Remove bowl screw (11) and gasket (10). Then re-

move bowl (9), bowl gasket (8) and screen (7).

11. Remove cover plate screw (17) with gasket (18). Lift

off the cover (19), cover gasket (20), screen retainer,

(21), and screen (22).

12. Blow out all passages with compressed air.

INSPECTION:

Inspect pump parts as follows:

1. Top Cover and Pump Body - Make visual check for

cracks and breakage. Inspect for diaphragm flange warpage
by testing on a smooth flat surface. Examine all threaded

holes for stripped or crossed threads. Broken, damaged, or
severely warped castings must be replaced.

2. Valve and Cage Assemblies - Replace. Extent of wear
cannot be determined visually.

3. Strainer Screen - Replace. Inspect new screen for damage

or obstruction. Screen must fit snugly around inner edge.

4. Rocker Arm - Inspect for wear or scores at camshaft pad

and at pointof contact with link and pull rod.

5. Rocker Arm Pin and Washer - Replace bullet type pin with

head type pin and washer.

6. Link - Replace because amount of wear cannot be determined

visually.

7. Rocker Arm Spring - Replace. Spring may be weak from distor-

tion or corrosion.

8. Diaphragm - Always replace.

9. Gaskets and Oil Seal - Always replace gaskets and oil seal to

assure tight seals.

ASSEMBLY (AC):

1. Assemble link spacer (41) over fuel link (36). Place one vacuum

link (35 and 37) on each side of the fuel link. The hook ends of
the vacuum link should come together so that they surround the

fuel link. All link hooks should point in the same direction.
Place assembly of links and spacer between lobes of rocker arm

with one spacer washer (43) on the outer side of each vacuum

link. Slide rocker arm bushing (38) through holes in rocker arm,
spacer washers, and links.

2. Stand the pump body (39) on the bench, fuel flange down. Set

rocker arm spring in position with one end over cone cast into

body. Slide rocker arm and link assembly into body. Outer end
of all link hooks must point toward vacuum flange. Temporar-

ily retain rocker arm and link assembly with AC tool PT-6 or a

long straight pin or 1 punch.

3. Turn the pump body over so the fuel diaphragm flange is up.

Set the diaphragm spring (1) on the staked-in oil seal. Push

diaphragm pull rod through retainer (12), spring and oil seal.

Flat of pull rod must be at right angles to link. Hook diaphragm
pull rod to fuel link. FUEL LINK IS THE SHORT, CENTER

LINK. DO NOT TILT DIAPHRAGM PULL ROD
EXCESSIVELY AS THIS MAY DAMAGE THE OIL

SEAL.

4 - 36 FUEL SYSTEM & EXHAUST

Содержание 1948 - 1952













































































































































































































































































































































Результаты поиска

Содержание 1948 - 1952

Отзывы:

Бренды по названию

Популярные бренды

Hudson 1948 - 1952, Руководство по обслуживанию

Результаты поиска

Содержание 1948 - 1952

Отзывы:

Бренды по названию

Популярные бренды