manualshive.com logo in svg

Hudson 1948 - 1952, Руководство по обслуживанию

Поделиться
Скачать
Hudson 1948 - 1952 Скачать руководство пользователя страница 118

3. Remove cam lever pin rivet plug (J) retainer (H), and pin 

(I).

4. Remove cam lever (B).

5. Remove six valve housing screws (P) and valve housing 

(M).

6. Remove two valve housing cover attaching screws (K), 

valve housing cover (R), outlet air dome diaphragm (Q) 
and strainer (0).

7. Remove diaphragm assembly (G).

8. Do not remove valve cage assemblies (L and N) unless 

they are to be replaced.

9. Clean all parts in gasoline. (Do not use strong solvent or 

cleaner on valve housing unless the valve cage assem-

blies have been removed.)

10. Inspect parts for wear and select repair kit. (One rebuild-

ing kit is a gasket and diaphragm kit; the other contains 

all parts which are subject to wear.)

FUEL PUMP ASSEMBLY (CARTER):

1. Install new valve cage assemblies (L and N) if they have 

been removed.

2. Assemble strainer (0), outlet air dome diaphragm (Q), 

valve housing cover (R) and attach to valve housing.

3. Install diaphragm assembly .(G) in pump body with flat 

spaces on sides toward ports.

4. Align mark on pump body with mark on valve housing 

(M) and Install housing, but DO NOT tighten screws.

5. Install cam lever, pin, and pin retainer.

6. Install new rivet plug (J).

7. Flex diaphragm and hold in maximum down position 

and tighten valve housing attaching screws.

8. Install cam lever return spring

FUEL PUMP DISASSEMBLY (AC):

CAUTION: Before taking a combination pump apart, 
read assembly instructions paragraphs No. 2, 13 and 15 
for special equipment needed. These are AC tools No. 
Pt-8, and two 10-32 x 1-1/211 screws. If you do not have 
these tools, or equivalent, do not attempt to overhaul the 
pump.

1. Mark edges of fuel cover (25), Figure 106, and body 

diaphragm flanges with a file. The parts may then be 

reassembled in the same relative position.

2. Remove fuel cover screws (23) and lock-washers. Sepa-

rate cover from body by jarring cover loose with a screw-

driver handle. Remove diaphragm spring (28) and 

retainer (29). Remove valve cage retainer screw and 
remove retainer and cage assemblies (27) and gaskets 

(26),

3. Mark edges of vacuum cover (6) and body diaphragm 

flanges. The parts may then be reassembled in the same 
relative position.

4. Remove two screws from opposite sides of the vacuum 

cover, and substitute for them two No. 10-32 x 1-1/2 

inch fillister head screws. Turn the two long screws all 
the way down, and then remove the balance of the 

regular cover screws. Alternately back off the two long 
screws, a few turns at a time, until the force of the heavy 

vacuum diaphragm spring is no longer effective. Remove 

the two long screws, the cover assembly, diaphragm 
spring (1), and spring retainer (12).

5. File riveted end of rocker arm pin (33) flush with steel 

washer, or drill of end with 3/8" drill. Drive out rocker 

arm pin with a drift punch. Wiggle rocker arm (42) 
until Slinks unhook from both diaphragms. Then re-

move rocker arm spring (40), rocker arm, and the link 
assembly.

6. Remove bushings (38) from rocker arm before removing 

rocker arm (42), two vacuum links (35 and 37), one fuel 

link (36), link spacer (41), and link washer (43).

4 - 34   FUEL SYSTEM & EXHAUST

Содержание 1948 - 1952














































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды