Hudson 1948 - 1952 Скачать руководство пользователя страница 235

Страница: 235 / 333

OVERDRIVE 9 - 27

ELECTRICAL

CONDITION NO. 3

OVERDRIVE DOES NOT ENGAGE:

A. Disconnect wire from "A" terminal of generator and connect

loose end of wire to negative post of battery by means of a

jumper.

B. Install test harness at overdrive relay and ground the No. 2

terminal of harness. If relay does not click, check •wiring
between relay and "A" terminal of regulator by connecting a

test lamp between the relay No. 3 terminal and ground. If
lamp lights but relay does not click, replace relay. If relay

clicks, but solenoid does not click, follow procedure F. If

both relay and solenoid click, make check C.

C. Leave generator wire connected as in A but remove test

harness from overdrive relay and Install it at the kickdown

switch. Ground the No. 1 and No. 4 terminals of the kick-
down switch in turn. If no click results, it indicates a defective

wire or poor terminal connection between the kickdown

switch and overdrive relay. If a click results from grounding
one terminal, but not from grounding the other, it indicates

an open kickdown switch. If a click results as the two termi-
nals are grounded in turn make check D.

D. Make similar test at overdrive control switch (test harness not

required). If an open switch is indicated, note Condition No.
1 before discarding switch. If click results as the two termi-

nals are grounded in turn -

E. Ground the governor terminal. If no click results it indicates

defective wire or terminal connections between the governor
and the control switch. If relay clicks, replace governor un-

less governor drive pinion is found to be missing or governor
drive gear is slipping.

F. If, in procedure 7-B, relay clicked but solenoid did not, con-

nect a test lamp between relay terminal No. 4 and ground. If

test lamp does not light when relay clicks, inspect relay fuse;
replace it if necessary. If fuse is good, connect the test lamp

between ground and each of the fuse clips in turn. If lamp
does not light at either fuse clip, inspect wire between relay

terminal No. 1 and voltage regulator terminal "B". If lamp

lights at each fuse clip. replace relay.

inspect relay fuse; replace it if necessary. If fuse is good,

connect the test lamp between ground and each of the

fuse clips in turn. If lamp does not light at either fuse clip,
inspect wire between relay terminal No. 1 and voltage

regulator terminal "B". If lamp lights at each fuse clip.

replace relay.

G. If lamp lit in the first part of test F, connect test lamp

between solenoid terminal No. 4 (the terminal with the

1/4" diameter screw) and ground. If lamp does not light
when relay clicks a defective wire between relay terminal

No. 4 and solenoid terminal No. 4 is indicated. If lamp
does light it indicates a defective solenoid or connections.

Remove solenoid cover, examine solenoid contacts,

clean if necessary, reconnect and test again for clicks
before discarding solenoid.

CONDITION NO. 8

FAILS TO SHIFT OUT OF OVERDRIVE BELOW 16-21
M. P. H.

CAUTION: If this condition actually exists car will not
roll backward and any attempt to force it to do so may
seriously damage the overdrive unit itself.

A. Check for this condition by rolling the car backward by

hand with the gear shift lever in neutral. If it will roll forward
but not backward, disconnect the wires at No. 4 terminal of

solenoid and loosen the solenoid and loosen the solenoid
mounting screws. If this does not unlock the transmission,

remove the mounting screws completely and pull straight out

on solenoid to disengage the solenoid pawl from slot in the
overdrive stationary gear.

If solenoid pulls free from transmission in this operation

without having been rotated 1/4 turn, indicates that the
solenoid was improperly Installed (solenoid stem was not

engaging pawl). See Condition No. 4 "Improper Installation
of Solenoid".

Содержание 1948 - 1952













































































































































































































































































































































Результаты поиска

Содержание 1948 - 1952

Отзывы:

Бренды по названию

Популярные бренды

Hudson 1948 - 1952, Руководство по обслуживанию

Результаты поиска

Содержание 1948 - 1952

Отзывы:

Бренды по названию

Популярные бренды