manualshive.com logo in svg

Hudson 1948 - 1952, Руководство по обслуживанию

Поделиться
Скачать
Hudson 1948 - 1952 Скачать руководство пользователя страница 311

BRAKES   15 - 5

WHEEL CYLINDERS

(FRONT)

REMOVAL:

1. Remove wheel and hub and drum.

2. Disconnect brake hose at frame bracket.

3. Using tool KMO-526, remove brake shoe retracting 

springs (39) Figure 1%y placing large end of tool over the 
anchor pin with the disengaging lug in the opening of the 

spring hook, rotate the tool 90 degrees and pull outward, 

Figure 5.

FIGURE 5

4. Remove the two wheel cylinder attaching screws.

5. Remove the connecting links between cylinder pistons 

and brake shoes. Wheel cylinder and hose maybe with-
drawn as a unit.

    To Install, Reverse Procedure of Removal.

NOTE: When installing the brake shoe retracting 
springs, use KMO-526 Replacer. Position small end of 
tool over anchor pin, place spring hook over shaft of tool 
and pry spring into position, Figure 6.

FIGURE 6

WHEEL CYLINDERS

(REAR)

NOTE: Use same procedure as shown for "Front Cylin-
der Removal & Installation" except item 2.

DISASSEMBLY:

1. Remove cylinder end guards (2), Figure 4.

2. Remove pistons (3).

3. Remove piston cups (4).
4. Remove piston cup springs (5).

    Check condition of rubber parts, and the cylinder bore for 

scratches or pits. Cylinder walls that are scratched or pitted 

should be honed or replaced.

ASSEMBLY:

1. Wash wheel cylinder and parts in c1ean alcohol.
2. Dip wheel cylinder and all parts in "Hudson Hydraulic 

Brake Fluid" for lubrication. Use new rubber cups.

3. Assemble as shown in Figure 4.

NOTE: The wheel cylinder screws should be tightened 
with torque wrench J-1300 at 12 foot pounds.

Содержание 1948 - 1952














































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды